Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
I am planning to do solaris 11 global zone patching having solaris 10 branded zone. I have a doubts on step 8 specially
Can someone clear my step 8 doubts or if anything wrong between step 1 to step 9 please correct that also as I have pretty good idea about Step 10 mean patching in solaris 10... (2 Replies)
So this is Solaris 11.1. I have a Global zone that has several non-global zones running in it. I want to change the capped-memory.physical resources setting in ALL the zone configs of the running zones.
if I were to do this manually here's what I would do:
zonecfg -z zone1
select... (2 Replies)
can some one help me out as it is showing 2 different time zones in global zone and nonglobal zone .In global zone it is showing in GMT while in nonglobal zone i it showing as PDT.
System in running with solaris 10 (3 Replies)
Hi Greetings...
I have an issue in connecting the zone from outside the network and it is because of default gateway. I can ping default gateway from inside the zone and not able to ping from global zone due to different VLAN issue. If i add two different gateways and restart network services,... (2 Replies)
Hi All
There is one folder in global zone I just want to share the same folder innon global zone. How can i do it?
pls send me script for this. (2 Replies)
Hi Gurus
I am not able to ping the local zone from global zone
when i am trying to ping i am getting below
ICMP Host Unreachable from gateway zone ( 192.268.35.210)
for icmp from zone ( 192.168.35.210) to sun1 ( 192.168.35.210)
However i can ping local zone from global
please... (12 Replies)
Hi All,
When i was installing patches in the Solaris 10 machine.
It does not install properly and gave the below message
===========================================
Approved patches will be installed in this order:
126868-02
Preparing checklist for non-global zone check...
Checking... (1 Reply)
native(5) Standards, Environments, and Macros native(5)NAME
native - native branded zone
DESCRIPTION
The native brand uses the branded zones framework described in brands(5) to run zones installed with the same software as is installed in
the global zone. The system software must always be in sync with the global zone when using a native brand.
SUB-COMMANDS
The following native brand-specific subcommand options are supported in zoneadm(1M).
attach [-u] [-b patchid]...
For native zones, zoneadm checks package and patch levels on the machine to which the zone is to be attached. If the packages/patches
that the zone depends on from the global zone are different (have different revision numbers) from the dependent packages/patches on
the source machine, zoneadm reports these conflicts and does not perform the attach. If the destination system has only newer dependent
packages/patches (higher revision numbers) than those on the source system, you can use the -u option to update the attached zone to
match the -revision packages and patches that exist on the new system. With -u, as in the default behavior, zoneadm does not perform an
attach if outdated packages/patches are found on the target system.
For native zones, one or more -b options can be used to specify a patch ID for a patch installed in the zone. These patches will be
backed out before the zone is attached or, if -u was also specified, updated.
install [-a archive] | [-d path] [-p] [-s] [-u] [-v] [-b patchid]...
The native brand installer supports installing the zone from either the software already installed on the system or from an image of an
installed system running the same release. This can be a full flash archive (see flash_archive(4)) or a cpio(1) or pax(1) "xustar" ar-
chive. The cpio archive be compressed with gzip or bzip2. The image can also be a level 0 ufsdump(1M), a path to the top-level of a
system's root tree, or a pre-existing zone path.
With no options the zone is installed using same software as is running the global zone.
To install the zone from a system image either the -a or -d is required. Either the -u or -p option is also required in this case.
-a archive
The path to a flash_archive(4), cpio(1), or pax(1) "xustar" archive, or a level0 ufsdump(1M), of an installed system. cpio archives
may be compressed using gzip or bzip2.
-b patchid
One or more -b options can be used to specify a patch ID for a patch installed in the system image. These patches will be backed
out during the installation process.
-d path
The path to the root directory of an installed system. If path is a hyphen (-), the zonepath is presumed to be already populated
with the system image.
-p
Preserve the system configuration after installing the zone.
-s
Install silently.
-u
Run sys-unconfig(1M) on the zone after installing it.
-v
Verbose output from the install process.
ATTRIBUTES
See attributes(5) for a description of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWzoneu |
+-----------------------------+-----------------------------+
|Interface Stability |Uncommitted |
+-----------------------------+-----------------------------+
SEE ALSO cpio(1), pax(1), zlogin(1), zonename(1), sys-unconfig(1M), ufsdump(1M), zoneadm(1M), zonecfg(1M), flash_archive(4), attributes(5),
brands(5), privileges(5), zones(5), lx_systrace(7D)SunOS 5.11 13 Feb 2009 native(5)