8 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hello,
I have been given a scripting project, but have not learned any scripting. I need to get some ideas on how to start. Attached is part of the project:
I have no idea how to parse the arguments. What I had in mind was to get the arguments ($1, $2, ... ) and have if statements for different... (1 Reply)
Discussion started by: facepalm
1 Replies
2. UNIX and Linux Applications
Dear all,
i am in last year of electronics department in engineering faculty
i need suggestions for a graduation project based on unix or free bsd or linux and electronics "embedded linux "
i think about embedded unix for example or device drivers
please i need helps (1 Reply)
Discussion started by: MOHA-1
1 Replies
3. Solaris
Hello,
I wrote a script which monitor the keyswitch state repeatedly each 10 minutes.
I'm extracting the keyswitch status by using prtdiag.
The script works fine for Netra v440 , but I found that prtdiag under Netra 1290 don't give keyswitch status.
unlike Netra 440 server , I found that... (2 Replies)
Discussion started by: Alalush
2 Replies
4. Solaris
so i've grabbed this sun netra t1 for some small dev work. now obviously i need to install sol10. no problem done it a million times except for the fact that i've never actually done it w/o a term server. so i grab a usb to serial and a serial to rj45 (the one you get in every cisco order.. roll... (24 Replies)
Discussion started by: pupp
24 Replies
5. What is on Your Mind?
guys - not sure where to post this one but i figured this was the likely spot.
i need a sun dvd slimline for netra t1. hcl matrix has this for production/manufac. number: X7288A / 540-5014.
anyone have a good spot to get this stuff? does anyone have an extra laying around to sell? i hate going... (2 Replies)
Discussion started by: pupp
2 Replies
6. Shell Programming and Scripting
i need to compare to dates/times given in the format MMDDhhmmYY. That is month, day, hour, minute, year. It is a 24 hour clock. I need to compare two dates to check that they are, say, less than 900 seconds apart. I have got to a point where it checks the time, turns the values into seconds and... (5 Replies)
Discussion started by: fwabbly
5 Replies
7. Cybersecurity
Hi,
I installed sybase server on a LINUX server. I assigen port 2025 whilst installation for sybase , later i uninstalled sybase and when i try to reinstall sybase and use port 2025 it throw up error saying that it is already in use, use other port number. How can I re-use the same port number... (2 Replies)
Discussion started by: suda
2 Replies
8. Shell Programming and Scripting
I have several staging directories on my UNIX server.
/usr2/data1
/usr2/data2
/usr2/data3
/usr2/data4
/usr2/data5
/usr2/data6
In these directories a file is transferred from different PC's connected to the network via TCP/IP. The File name is constant for all directories.
Transfers... (1 Reply)
Discussion started by: Docboyeee
1 Replies
dxpower(8) System Manager's Manual dxpower(8)
NAME
dxpower - controls energy saving features on systems that can be power managed
SYNOPSIS
/usr/bin/X11/dxpower
DESCRIPTION
The Power Manager application, dxpower, is used to maintain and manage the power management features on computers and peripherals that can
be power managed.
Power Manager lets you place monitors in three power saving modes: Standby, Suspend, or Off and lets you selectively spin down inactive
disks to reduce power consumption. You also can specify when you want power management features to be active: always, never, or only at a
specific time of day.
Privileged (root) users have the capability to set system wide power management values. Non-privileged users set power management values
on their monitors for the current log in session.
The Power Manager application can be invoked from: The CDE Application Manager Application Group: System_Admin System Admin Subgroup: Dai-
lyAdmin
If you are not using CDE, start Power Manager from the command line: # /usr/bin/X11/dxpower
For more information about how to use the Power Manager application, start the application and click on the Help button.
An alternative to using the Power Manager application is to set and control power management attributes from the command line by using the
sysconfig command. Refer to System Administration for more information about setting and controlling power management from the command
line.
SEE ALSO
Commands: sysconfig(8)
System Administration
dxpower(8)