02-08-2008
Netra X1 will not power on - any ideas?
Hi,
I have a Netra X1 that will not power on - either using the toggle switch or by using the "poweron" command at the LOM prompt. Has anyone seen this behaviour before or better still how to fix it.
The LOM seems to be functioning fine but I cannot get the box to powerup. I thought it might be the powersupply but I have tested the P/S on a second X1 and it works fine.
Any thoughts?
Gareth
8 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
I have several staging directories on my UNIX server.
/usr2/data1
/usr2/data2
/usr2/data3
/usr2/data4
/usr2/data5
/usr2/data6
In these directories a file is transferred from different PC's connected to the network via TCP/IP. The File name is constant for all directories.
Transfers... (1 Reply)
Discussion started by: Docboyeee
1 Replies
2. Cybersecurity
Hi,
I installed sybase server on a LINUX server. I assigen port 2025 whilst installation for sybase , later i uninstalled sybase and when i try to reinstall sybase and use port 2025 it throw up error saying that it is already in use, use other port number. How can I re-use the same port number... (2 Replies)
Discussion started by: suda
2 Replies
3. Shell Programming and Scripting
i need to compare to dates/times given in the format MMDDhhmmYY. That is month, day, hour, minute, year. It is a 24 hour clock. I need to compare two dates to check that they are, say, less than 900 seconds apart. I have got to a point where it checks the time, turns the values into seconds and... (5 Replies)
Discussion started by: fwabbly
5 Replies
4. What is on Your Mind?
guys - not sure where to post this one but i figured this was the likely spot.
i need a sun dvd slimline for netra t1. hcl matrix has this for production/manufac. number: X7288A / 540-5014.
anyone have a good spot to get this stuff? does anyone have an extra laying around to sell? i hate going... (2 Replies)
Discussion started by: pupp
2 Replies
5. Solaris
so i've grabbed this sun netra t1 for some small dev work. now obviously i need to install sol10. no problem done it a million times except for the fact that i've never actually done it w/o a term server. so i grab a usb to serial and a serial to rj45 (the one you get in every cisco order.. roll... (24 Replies)
Discussion started by: pupp
24 Replies
6. Solaris
Hello,
I wrote a script which monitor the keyswitch state repeatedly each 10 minutes.
I'm extracting the keyswitch status by using prtdiag.
The script works fine for Netra v440 , but I found that prtdiag under Netra 1290 don't give keyswitch status.
unlike Netra 440 server , I found that... (2 Replies)
Discussion started by: Alalush
2 Replies
7. UNIX and Linux Applications
Dear all,
i am in last year of electronics department in engineering faculty
i need suggestions for a graduation project based on unix or free bsd or linux and electronics "embedded linux "
i think about embedded unix for example or device drivers
please i need helps (1 Reply)
Discussion started by: MOHA-1
1 Replies
8. Shell Programming and Scripting
Hello,
I have been given a scripting project, but have not learned any scripting. I need to get some ideas on how to start. Attached is part of the project:
I have no idea how to parse the arguments. What I had in mind was to get the arguments ($1, $2, ... ) and have if statements for different... (1 Reply)
Discussion started by: facepalm
1 Replies
PSIZE(1) PDB2PQR Manual PSIZE(1)
NAME
psize - Get dimensions and other information from PQR files
SYNOPSIS
psize [--cfact=value] [--fadd=value] [--space=value] [--gememfac=value] [--gememceil=value] [--ofrac=value] [--redfac=value] {pqrfile}
psize {--help | -h}
DESCRIPTION
psize derives information from PQR files to preprare the models of proteins and chemicals for electrostatics calculations. The tool
calculates dimensions for coarse and fine grids, grid spacings, box size and estimates the memory required to perform an electrostatics
calculation.
The calculation of this information can be influenced by giving constraints to psize as parameters.
OPTIONS
psize accepts the following options:
--help, -h
Print a help message and exit.
--cfact=value
Factor by which to expand the molecule dimensions to get the coarse grid dimensions
--fadd=value
Amount to add to the molecule dimensions to get the fine grid dimensions.
--space=value
Desired fine mesh resolution.
--gememfac=value
Number of bytes per grid point required for sequential MG calculation.
--gememceil=value
Maximum MB allowed for sequential MG calculation. Adjust this to force the script to perform faster calculations (which require more
parallelism).
--ofrac=value
Overlap factor between mesh partitions.
--redfac=value
Maximum factor by which a domain dimension can be reduced during focusing.
SEE ALSO
apbs(1), pdb2pqr(1)
AUTHOR
Manuel Prinz <debian@pinguinkiste.de>
Wrote this manpage for the Debian System.
COPYRIGHT
Copyright (C) 2008 Manuel Prinz
psize 2008-06-04 PSIZE(1)