9 More Discussions You Might Find Interesting
1. Solaris
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
2. Solaris
I have a service that resides in both the global and non global zones. When I disable the service in the global zone, a svcs -p on that service shows the process name and ID of the svcadmd for the non global. An svcs -l on the service in the global shows online with an intended state of disabled.... (0 Replies)
Discussion started by: Cbrown31
0 Replies
3. UNIX for Advanced & Expert Users
Dear all,
recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes.
I did the following:
host1:
$ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed
$ zpool export zone1
host2:
$ zpool... (2 Replies)
Discussion started by: custos
2 Replies
4. Solaris
can some one help me out as it is showing 2 different time zones in global zone and nonglobal zone .In global zone it is showing in GMT while in nonglobal zone i it showing as PDT.
System in running with solaris 10 (3 Replies)
Discussion started by: ravijanjanam12
3 Replies
5. Solaris
I have two physical servers, with zones that mount local storage.
We were using "raw device" in the zonecfg to point to a metadevice on the global zone (it was not mounted in the global zone at any point).
It failed to mount on every boot because the directory existed in the zone.
I... (6 Replies)
Discussion started by: BG_JrAdmin
6 Replies
6. Solaris
Hi Greetings...
I have an issue in connecting the zone from outside the network and it is because of default gateway. I can ping default gateway from inside the zone and not able to ping from global zone due to different VLAN issue. If i add two different gateways and restart network services,... (2 Replies)
Discussion started by: vvpotugunta
2 Replies
7. Solaris
Do I need to reinstall/rerun JASS after upgrading from Sol9 to Sol10?
Just wondered if the upgrade procedure overwrote any of the settings etc? (0 Replies)
Discussion started by: psychocandy
0 Replies
8. UNIX for Advanced & Expert Users
Greetings Forumers!
I ran into an issue after running luupgrade on v880 running Solaris 8. I want to upgrade to Solaris 10.
When I rebooted the system I noticed the file systems listed as such:
# df -h
Filesystem size used avail capacity Mounted on
/dev/dsk/c1t1d0s0 ... (2 Replies)
Discussion started by: bluescreen
2 Replies
9. Solaris
Hello All:
I am trying to configure mail service on Solaris 10 and I am unable to send using mailx. It appears the server may not be listening on port 25:
bash-3.00# mconnect
connecting to host localhost (127.0.0.1), port 25
connect: Connection refused
services is configured to use port... (7 Replies)
Discussion started by: hoo5091
7 Replies
GNUNET-ARM(1) General Commands Manual GNUNET-ARM(1)
NAME
gnunet-arm - control GNUnet services
SYNOPSIS
gnunet-arm [options]
DESCRIPTION
gnunet-arm can be used to start or stop GNUnet services, including the ARM service itself. The ARM service is a supervisor for GNUnet's
service processes. ARM starts services on-demand or as configured and re-starts them if they crash.
OPTIONS
-c FILENAME, --config=FILENAME
Use the configuration file FILENAME.
-e, --end
Shutdown all GNUnet services (including ARM itself). Running "gnunet-arm -e" is the usual way to shutdown a GNUnet peer.
-h, --help
Print short help on options.
-L LOGLEVEL, --loglevel=LOGLEVEL
Use LOGLEVEL for logging. Valid values are DEBUG, INFO, WARNING and ERROR.
-i SERVICE, --init=SERVICE
Starts the specified SERVICE if it is not already running. More specifically, this makes the service behave as if it were in the
default services list.
-k SERVICE, --kill=SERVICE
Stop the specified SERVICE if it is running. While this will kill the service right now, the service may be restarted immediately
if other services depend on it (service is then started 'on-demand'). If the service used to be a 'default' service, its default-
service status will be revoked. If the service was not a default service, it will just be (temporarily) stopped, but could be re-
started on-demand at any time.
-s, --start
Start all GNUnet default services on this system (and also ARM). Naturally, if a service is demanded by a default service, it will
then also be started. Running "gnunet-arm -s" is the usual way to start a GNUnet peer.
-I, --info
List all running services.
-v, --version
Print GNUnet version number.
BUGS
Report bugs by using Mantis <https://gnunet.org/bugs/> or by sending electronic mail to <gnunet-developers@gnu.org>
SEE ALSO
gnunet-service-arm(1)
GNUnet Jan 4, 2012 GNUNET-ARM(1)