10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
2. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
3. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
4. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
5. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
8. IP Networking
What are the steps between "ifconfig eth0 UP" and "net_device->open"?
ifconfig eth0 UP =>
ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) =>
????? => what are these steps?
net_device->open
Thanks! (1 Reply)
Discussion started by: samuncle
1 Replies
9. Gentoo
Hi all,
I'm trying to write a script that will turn off the network interface eth0 on a linux Gentoo machine and then turn it back on, any help?
Thanks,
Neked (1 Reply)
Discussion started by: neked
1 Replies
10. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
if_mpadm(1M) System Administration Commands if_mpadm(1M)
NAME
if_mpadm - change operational status of interfaces within a multipathing group
SYNOPSIS
/usr/sbin/if_mpadm -d interface_name
/usr/sbin/if_mpadm -r interface_name
DESCRIPTION
Use the if_mpadm utility to change the operational status of interfaces that are part of an IP multipathing group. If the interface is
operational, you can use if_mpadm -d to detach or off-line the interface. If the interface is off-lined, use if_mpadm -r to revert it to
its original state.
When a network interface is off-lined, all network access fails over to a different interface in the IP multipathing group. Any addresses
that do not failover are brought down. Network access includes unicast, broadcast, and multicast for IPv4 and unicast and multicast for
IPv6. Addresses marked with IFF_NOFAILOVER do not failover. They are marked down. After an interface is off-lined, the system will not use
the interface for any outbound or inbound traffic, and the interface can be safely removed from the system without any loss of network
access.
The if_mpadm utility can be applied only to interfaces that are part of an IP multipathing group.
OPTIONS
The if_mpadm utility supports the following options:
-d interface_name Detach or off-line the interface specified by interface_name.
-r interface_name Reattach or undo the previous detach or off-line operation on the interface specified by interface_name. Unless
the -d option was used to detach or off-line the interface, this option will fail.
EXAMPLES
Example 1: Detaching an Interface
Use the following command to off-line or detach the interface. All network access will failover from hme0 to other interfaces in the same
IP multipathing group. If no other interfaces are in the same group, the operation will fail.
example% if_mpadm -d hme0
Example 2: Reattaching an Off-line Interface
Use the following command to undo the previous operation. Network access will failback to hme0.
example% if_mpdadm -r hme0
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Unstable |
+-----------------------------+-----------------------------+
SEE ALSO
ifconfig(1M), in.mpathd(1M), attributes(5)
DIAGNOSTICS
off-line failed as there is no other functional interface available in the multipathing group for failing over the network access.
This message means that other interfaces in the group are failed over already or the multipathing configuration was not suitable for com-
pleting a failover.
off-line cannot be undone because multipathing configuration is not consistent across all the interfaces in the group.
This message means that some interfaces in the IP multipathing group are not configured consistently with other interfaces in the group,
for example, one of the interfaces in the group does not have an IFF_NOFAILOVER address.
SunOS 5.10 3 Sep 2002 if_mpadm(1M)