just installed solaris 11.1 (11.1.9.5.1) on a sun7410 ZFSSA (x4440 + j4400), but when I enable multipathing with "stmsboot -e", only the 1TB SATA drives inside the j4400 are configured as multipathed vhci / mpxio devices, but the logzillas / ZeusIOPS drives are skipped. the server is connected with two SAS HBAs to the j4400 storage
Found a setting on another ZFSSA running the fishworks solaris os (Solaris 11 Express snv_151 || ZFSSA 2011.1.6) in the kernel.drv directory:
I've tried these settings on the solaris 11.1 installation, also with 'mpxio-disable="no";' and 'disable-sata-mpxio="no";' in /kernel/drv/mpt.conf & /kernel/drv/mpt_sas.conf, but solaris fails to enable the multipathing...
it should work, the ZFSSA uses the vhci path:
no 'mpathadm' to prove the 2nd path on the ZFSSA solaris...
tried several variations in the sd.conf, but it doesn't work:
Did I forget so tell solaris somewhere to look into that sd.conf file... running out of ideas, any hints?
Hi,
I have Solaris-9 server, V240.
I got alert that one of the interface on IPMP configuration, is failed. Found that two IPs (192.168.120.32 and 192.168.120.35) are not pingable from this server. These two IPs were plumbed on another server and that is decommissioned now. That is the reason,... (5 Replies)
Dear all,
I have a solaris 10 in my environment (VMware virtual machine). recently I increased the harddisk size from the VMware and reboot my server. after reboot the os is unable to boot and gives the below error message.
exec(/sbin/init) file not found
press any key to restart
... (3 Replies)
I was installing Solaris-10 Recommended patch Cluster and it came out without installling all patches. I gave a rebooted and tried installing it again, but it seems some lock or something is prevenventing to install further patches. I am not able to figure out and I am struck in between... (4 Replies)
1) I got error when run
gmake hello
ld.so.1: gmake: fatal: libintl.so.8: open failed: No such file or directory
Killed
2) # uname -a
SunOS 5.9 Generic_122300-47 sun4u sparc SUNW,Netra-T12
3) I downloaded an unzip the files to /tmp/mm
then
from /tmp/mm
I run
1) pkgadd -d... (8 Replies)
Hai
we using emc storage which is conneted to M5000 through san switch.
we asign 13 luns but in server it is showing 22 luns.
i enable the solaris multipathing (MPxIO)
#more /kernel/drv/fp.conf in that file
MPxio-disable=no
#mpathadm list lu
it shows ... (2 Replies)
Dear UNIX Gurus
I need to know how to disable MPXIO feature (Inbuilt multipathing software of Solaris 10) as we are going to implemented iSCSI EMC based SAN. I am bit new to this feature so kindly suggest how to disable it
Regards (4 Replies)
Hi,
I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation .
I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2.
Now is it possible to have IP Multipathing on each of the servers as follows ?
... (0 Replies)
Hello All,
I work for a Health care company at a local trauma hospital. I maintain a Picture Archiving and Communication System (PAC's). Basically, any medical images (X-Ray, CT, MRI, Mammo, etc) are stored digitally on the servers for viewing and dictation from diagnostic stations. I took over... (10 Replies)
I have solaris 10 sparc. I installed a Qlogic hba card.
This card is connected on a brocade switch and the brocade is connected on 2 different controllers on a Hitachi disk bay.
I formated 2 luns. On my solaris system, i have 4 disk.
How to configure solaris 10 to fix the dual disk view.
... (4 Replies)
I've setup Solaris IP Multipathing under Solaris whenever the hardware to do so was available. I find it amazing though that so few places I've worked at don't use it until I arrive. I wanted to find out if I'm running into all the exceptions, or is it really not being used? ... (3 Replies)