10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I have Sun Solaris V440, every two days or so, the system crashes and it's at OK prompt. After that I do the FSCK and clear all the bad sectors. Then system stays up for close to 48 hours. Then it crashes again. I checked the logs and I don't see anything under /var/adm/messages file.
... (1 Reply)
Discussion started by: samnyc
1 Replies
2. Solaris
Dear friends,
I have the DVD image of solaris 10 but I don't have DVD writer to burn it onto a dvd R. I was wondering if I could install Solaris from my 4gb usb flash drive as my PC supports booting from usb. I have installed Windows 7 this way recently, I have no idea about Solaris. Could you... (2 Replies)
Discussion started by: gabam
2 Replies
3. Solaris
I have a Sun SunFire v440 server with a hard drive in each slow. When I run "iostat -En", "format", and "cfgadm -al", 3 of the drives show up, but the one in Slot 1( which should be c1t1d0 ) is nowhere to be found.
However, when I go to the rack its in an watch the activity lights, it seems... (2 Replies)
Discussion started by: the.gooch
2 Replies
4. Solaris
Hello,
I've a very weird problem with one of the machines. When I try to boot off a working DVD that I used to install another system with it spits out the following message:
Sun Fire V440, No Keyboard
Copyright 2007 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.22.33, 8192 MB... (14 Replies)
Discussion started by: stoci
14 Replies
5. Solaris
Hi
I had installed Sun Solaris 10 on my dell vostro 1400.Problem is iam unable to mount the usb drives as there was no detections at all.And also iam unable to find my network interface or iam not able to install the network card.
If try to type ifconfig -a
It is showing only loop back... (4 Replies)
Discussion started by: testerindia25
4 Replies
6. Solaris
I have a T2000 server running solaris 10, it has 4 USB ports. I want to extend the storage capacity by attaching an external USB drive and mounting it as an other mount point.
How do I do that, the following link gives information about USB in Solaris OS, ... (1 Reply)
Discussion started by: Tirmazi
1 Replies
7. Solaris
Hi-
I would like to know if anyone has used any USB External Hard Drive, about 500/750GB or 1TB, with any of the Solaris 10 "SPARC" systems. Not on intel nor amd platform.
I'm looking for the compatible drive and found a few listed on Sun solaris ready page, but I'd like to have inputs from... (3 Replies)
Discussion started by: agfa_109
3 Replies
8. Solaris
Is there a way to install Solaris 10 x86 with an external DVD drive that connects through the USB port? I would think I would run GRUB off of a floppy disk and somehow use that to make it look to the USB port to boot from but I don't know how to do that. Can anyone help me out? (1 Reply)
Discussion started by: Bradj47
1 Replies
9. Solaris
Hi Friends,
My solaris box V440 got stucked. I couldn't accessit from the remote console. Finally i restarted the box.
Can you tell me what are the ways we can find out the issues
and what are the logs we can check other than /var/log/messages.
Thanks
Jinu (1 Reply)
Discussion started by: Jinu
1 Replies
10. SCO
Can anybody help me out to mount USB flash /floppy drive in sco openserver 6.0 . (5 Replies)
Discussion started by: sureshdrajan
5 Replies
SMP_REP_MANUFACTURER(8) SMP_UTILS SMP_REP_MANUFACTURER(8)
NAME
smp_rep_manufacturer - invoke REPORT MANUFACTURER INFORMATION SMP function
SYNOPSIS
smp_rep_manufacturer [--help] [--hex] [--interface=PARAMS] [--raw] [--sa=SAS_ADDR] [--verbose] [--version] [--zero] SMP_DEVICE[,N]
DESCRIPTION
Sends a SAS Management Protocol (SMP) REPORT MANUFACTURER INFORMATION function request to a SMP target. The SMP target is identified by the
SMP_DEVICE and the SAS_ADDR. Depending on the interface, the SAS_ADDR may be deduced from the SMP_DEVICE. The mpt interface uses SMP_DEVICE
to identify a HBA (an SMP initiator) and needs the additional ,N to differentiate between HBAs if there are multiple present.
OPTIONS
Mandatory arguments to long options are mandatory for short options as well.
-h, --help
output the usage message then exit.
-H, --hex
output the response (less the CRC field) in hexadecimal.
-I, --interface=PARAMS
interface specific parameters. In this case "interface" refers to the path through the operating system to the SMP initiator. See
the smp_utils man page for more information.
-r, --raw
send the response (less the CRC field) to stdout in binary. All error messages are sent to stderr.
-s, --sa=SAS_ADDR
specifies the SAS address of the SMP target device. Typically this is an expander. This option may not be needed if the SMP_DEVICE
has the target's SAS address within it. The SAS_ADDR is in decimal but most SAS addresses are shown in hexadecimal. To give a number
in hexadecimal either prefix it with '0x' or put a trailing 'h' on it.
-v, --verbose
increase the verbosity of the output. Can be used multiple times
-V, --version
print the version string and then exit.
-z, --zero
zero the Allocated Response Length field in the request. This is required for strict SAS-1.1 compliance. However this option should
not be given in SAS-2 and later; if it is given an abridged response may result.
CONFORMING TO
The SMP REPORT MANUFACTURER function was introduced in SAS-1, with small additions in SAS-1.1 . This function remains unaltered in SAS-2
and SPL-1.
AUTHORS
Written by Douglas Gilbert.
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright (C) 2006-2011 Douglas Gilbert
This software is distributed under a FreeBSD license. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
POSE.
SEE ALSO
smp_utils, smp_discover(smp_utils)
smp_utils-0.96 May 2011 SMP_REP_MANUFACTURER(8)
