10 More Discussions You Might Find Interesting
1. Solaris
I have a SunFire V445 running Solaris 10 and am adding a Sun DLT tape drive. From the OK prompt the probe-scsi-all does see the drive and it is the proper target of 4. When I do the boot -- -r it does build the /dev/rmt directories correctly and the links to /devices appear correct as well. When I... (8 Replies)
Discussion started by: chastings
8 Replies
2. UNIX for Advanced & Expert Users
Hi All,
Seeking information on the following and perhaps a bit of insight and opinions:
I would like to look into using NDMP to backup a disk array using NetBackup 7.5 to HP B6200 StoreOnce Backup System (i.e. Virtual Tape Library) as well as physical tape library.
Does anyone think... (0 Replies)
Discussion started by: zixzix01
0 Replies
3. Solaris
Hello
I'm pretty new in Solaris 10 and we now have to add an FC-based library to the Solaris. As far as I am informed, we have restart the Sun with the command "boot-r", to detect new devices, right?
Then the library should be found automatically?
How can I check if the library has been... (4 Replies)
Discussion started by: pole23
4 Replies
4. Emergency UNIX and Linux Support
Hi All,
We have patched our solaris 10 u4 server with lustarter patch in order to get it prepared for solaris live upgrade.The patch installation went pretty fine and we did reboot the server after patching.But after patching we have noticed O.S is not able to detect tape library.Not sure what... (22 Replies)
Discussion started by: sahil_shine
22 Replies
5. Solaris
Hello,
i am trying to get following configuration up running, but get no access to the library roboter.
Server: SunOS 5.10 Generic_138889-03 i86pc i386 i86pc
DELL TL-2000: 1 Tape: IBM ULT3580-HH4 and Robot: 3573-TL,
connected via ISCSI Bridge (build into the TL)
... (1 Reply)
Discussion started by: austin73
1 Replies
6. Solaris
Hi everyone.
Im new to Sun Solaris or the Unix environment. My only background is the DOS command in windows and a little bit of c++ programming. I always worked with troubleshooting hardware and software issues with windows.
Now that I need to configure tape drives using sun solaris, I had... (11 Replies)
Discussion started by: graboid888
11 Replies
7. Solaris
How to implement NFS Security in server where filesystem is configured as NFS & AutoFS?
Any special patch need to be applied?
What are the procedures? (1 Reply)
Discussion started by: KhawHL
1 Replies
8. Solaris
Env:
Server : Sparc Ultra-80
OS: Solaris 10
Direct SCSI connection to Library. Terminator connected at the Tape End.
Problem: Unable to see any device file related to Robotic /dev/rsst0.
Unable to see any device file /dev/rmt.
------------
Messages while the machine boots
sst0: No... (3 Replies)
Discussion started by: amqstam
3 Replies
9. Filesystems, Disks and Memory
I have a Sun Ultra 10/Solaris 2.7 with a differential SCSI card connected to a Supter DLt1 Tape Drive. When I boot the machine, and I do a probe-scsi-all in the very beginning of the boot process. It shows up correctly. If I wait for the boot process to proceed and then I do a probe-scsi-all, I get... (1 Reply)
Discussion started by: brv
1 Replies
10. UNIX for Dummies Questions & Answers
I picked up this library but I cannot get the device to actuate.
How do I make this work with Solaris 7? (2 Replies)
Discussion started by: n9ninchd
2 Replies
suninstall(1M) System Administration Commands suninstall(1M)
NAME
suninstall - install the Solaris operating system
SYNOPSIS
suninstall
DESCRIPTION
install-solaris(1M) is now the preferred command for starting and restarting the Solaris Installation program. It should be used instead of
suninstall. suninstall is symbolically linked to install-solaris.
suninstall is a forms-based and graphical subsystem for installing the operating system.
suninstall exists only on the Solaris installation media (CD or DVD) and should only be invoked from there. Refer to the Solaris 10 Instal-
lation Guide: Basic Installations for more details.
suninstall allows installation of the operating system onto any standalone system. suninstall loads the software available on the installa-
tion media. Refer to the Solaris 10 Installation Guide: Basic Installations for disk space requirements.
USAGE
Refer to the Solaris 10 Installation Guide: Basic Installations for more information on the various menus and selections.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
SEE ALSO
pkginfo(1), install(1M), install-solaris(1M), pkgadd(1M), attributes(5)
Solaris 10 Installation Guide: Basic Installations
NOTES
It is advisable to exit suninstall by means of the exit options in the suninstall menus.
SunOS 5.10 9 Sep 2004 suninstall(1M)