How to assign multicast IP address

10 More Discussions You Might Find Interesting

1. IP Networking

Multicast IP address

Hi please help, theoretically I',m interested in starting a streaming service using multicast IP service. I'd like to know how do I get an IP address that I can send my data too? (please don't just point me too Internet Assigned Numbers Authority as ive been there and it just seem to state...

2. IP Networking

IPv6 address block assign/associate with an interface

Hello all, I am trying to receive (tcp/udp/sctp) traffic from all IPs and, eventually, all ports of an IPv6 address block using as few sockets as possible short of implementing my own network stack. One possible solution was to associate an IP block to an interface then bind to that...

3. Solaris

How to assign static ip address to the server having solaris 10. i.e. nge0

hi, how to assign static ip address to the server having solaris 10. assign static ip to nge0 which will sustain across reboots which will include all settings including gateway setting etc..

4. IP Networking

assign mac address for virtual interface eth1:0

Hi , by default the physical interface (eth1) and virtual interface eth1:0 will be having same mac address, is there any way we can assign separate mac addresses for both the interfaces. would some one help me out in this. Thanks Gopi

5. Solaris

Multicast address config lost

On Solaris OS, We use the following command to config the multicast address for NIC in order to process the multicast packets: # route add 228.228.228.228 10.101.10.2 Where " 228.228.228.228 " is the multicast for specified NIC ip 10.101.10.2 . Also use the netstat -nr, the above set could...

6. Solaris

How to assign MAC address to N/W interface in solaris

I m having interface ce0 ce1 and its sub interfaces for that. I want to give MAC addresses for the same. How will I assign it. Please give solution for the same

7. Solaris

multicast config

On SUN Solaris 10, if I want to multicast packets between nodes, whether it must config the multicast IP from OS, if yes, how to do it?

8. Linux

How to multicast on different IP network

On Linux, I have configured two different IP address for two network device eth0 ,eth1 , in my program, I want to multicast differently on these two network, I know it must add route for single network and I try to config another route for second network,but it can not work correctly, how to config...

9. UNIX for Dummies Questions & Answers

How to assign virtual address?.

Hello,I am new to unix,i want to know how to assign virtual ip address to a system that is in my personal network?

10. HP-UX

How to multicast on different IP network

Hi, there On HP-UX, I want to multicast packets on two different IP network repectively. The two NIC are configured with two different IP. The routes are added with one default and one net for each IP . The multisender programs bind their own local IP, multireceiver programs add the...

LEARN ABOUT HPUX

mrinfo

mrinfo(1M)																mrinfo(1M)

NAME

       mrinfo - Multicast Routing Configuration Information Tool

SYNOPSIS

       debuglevel] retries] timeout] [ multicast-router ]

DESCRIPTION

       requests  the configuration information from the multicast-ourter, and prints the information to the standard out.  multicast-router can be
       either an IP address or a system name.  sends out the ASK_NEIGHBORS igmp  message  to  the  specified  multicast-router,  when  the  router
       receives  the request, it sends back its configuration information. If the multicast-router is not specified, the request is sent the local
       router.

       The the configuration information for each interface is printed in the following format:

       If there are multiple neighbor routers on one interface, they will all be reported on the output.  The possible values for flag are:

       Neighbors are reached via tunnel.

       The tunnel uses IP source routing.

       The interface is down.

       The interface is administratively disabled for multicast routing.

       The local router is the querier of the subnet.

       Please see mrouted(1M) for and

       The command line options are:

       Sets the level for printing out the debug message. The default is 0,
		     only error and warning messages will be printed. Debug level three prints most the messages.

       Sets the retry times to pull the routing daemon for information. The
		     default is 3.

       Specifies the timeout value in seconds for waiting the reply. The default value
		     is 4.

EXAMPLE

       The following is an example of quering the multicasting configuration from the local routing daemon.

	      127.0.0.1 (localhost) [version 3.3]:
		15.13.106.144 -> 15.13.106.145 (hpntcbs.cup.hp.com) [10/1/querier]
		193.2.1.39 -> 0.0.0.0 (all-zeros-broadcast) [1/1/disabled]
		15.13.106.144 -> 15.255.176.33 (matmos.hpl.hp.com) [10/1/tunnel]
		15.13.106.144 -> 15.17.20.7 (hpspddc.vid.hp.com) [10/1/tunnel/down]

   Note
       must be run as root.

AUTHOR

       was developed by Van Jacobson.

SEE ALSO

       mrouted(1M), map-mbone(1M).

																	mrinfo(1M)

Solaris