10 More Discussions You Might Find Interesting
1. Solaris
I am working on VM host and collecting data to identify the type of storage attached to the server which will be migrated to VNX.
it has one ldom created on it
luxadm probe output ---
No Network Array enclosures found in /dev/es
Found Fibre Channel device(s):
Node... (7 Replies)
Discussion started by: kpatel786
7 Replies
2. UNIX for Dummies Questions & Answers
We can Know the storage devices in fdisk -l. But Please tell me how can i identify the SAN devices :wall:
How SAN devices are represented in the fdisk -l output :wall::wall:
Thanks in Advance........:D (3 Replies)
Discussion started by: vamshigvk475
3 Replies
3. Red Hat
Hi, I have many servers all of these are boot from SAN. Can anybody let me know that how to identify the server is Boot fron SAN and from which device?
Thanks
Rahul (1 Reply)
Discussion started by: rahul.kurumkar
1 Replies
4. Solaris
I have a solaris 10 box which does not have internal disks it has just a single dual port HBA card. Storage team has assigned 2 LUNs to the system and i can see it from the probe-scsi-all
/pci@3,700000/SUNW,emlxs@0,1
Device PortID 10100 WWPN 5006016941e0a08d
LUN 0 Disk DGC ... (0 Replies)
Discussion started by: fugitive
0 Replies
5. Red Hat
Hello,
How can I identify SAN disks not in use by the OS?
Thank you. (8 Replies)
Discussion started by: asanchez
8 Replies
6. UNIX for Dummies Questions & Answers
Hello everybody,
I'm using the binary inqraid (Linux RHEL) in order to retrieve information about SAN disks. The questions are:
Given an LDEV, how do I know if the SAN disk related to this LDEV is being used by the OS? I mean, how can I demonstrate to "Storage department" that all disks of... (4 Replies)
Discussion started by: asanchez
4 Replies
7. UNIX for Advanced & Expert Users
Hi There,
Has anyone had any luck with or know how to get AIX 5+ to boot from a HP EVA 6000 SAN?
The servers used here will be P Class Blades
My initial searches on this so far did not bring results so I am guessing this may not be possible on HP SAN's but please let me know if I am... (0 Replies)
Discussion started by: fazzasx
0 Replies
8. Solaris
My current situation is like this, I have a v440 connected to a netapp central storage 3140 via fiber channel, my OS and oracle is installed in the internal drive of the v440.
What I would like to do is to advertise another LUN in netapp to the v440 and let my v440 boot from it so I can start... (3 Replies)
Discussion started by: q8devilish
3 Replies
9. Red Hat
hi all,
i have qle 2460 hba card in my server. and i have a lun from promise array from raid 0. I want to boot my OS (rhel5.2-64 bit) lun on a dell t300 server. can some one help me on this please asap.. (0 Replies)
Discussion started by: navadeep
0 Replies
10. HP-UX
Hi all,
I am trying to configure my HPUX host 11.31 IA64 to boot from a LUN for EMC clariion CX3-80 (Flaire PNR 26).
I am following the below mentioned steps..
vi /tmp/idf
3
EFI 500MB
HPUX 100%
HPSP 400MB
idisk -f /tmp/idf -w /dev/rdisk/diskxxx
insf -e
pvcreate -B... (0 Replies)
Discussion started by: barun agarwal
0 Replies
sys_attrs_bparm(5) File Formats Manual sys_attrs_bparm(5)
NAME
sys_attrs_bparm - bparm subsystem attributes
DESCRIPTION
This reference page lists and describes attributes for the Boot Parameters (bparm) kernel subsystem. Refer to the sys_attrs(5) reference
page for an introduction to the topic of kernel subsystem attributes.
Identifies the device from which the system was last booted. This attribute corresponds to the console firmware environment vari-
able with the same name. Do not modify this value, which is set when the system boots.
A combination of flags that controls the boot loader and kernel. This attribute corresponds to the console firmware environment
variable with the same name. Values for the variable are: Boot to multiuser mode. By default, the kernel boots to single-user mode.
Enable the kdebug debugger to debug the kernel. By default, kdebug is not enabled in the kernel. Produce full dumps when the system
crashes. By default, partial dumps are produced. Prompt for an alternate kernel and special arguments when the system is booted. By
default, no questions are asked.
Set boot_osflags only at the console prompt or by using the consvar utility.
Identifies the boot device to be used when one is not included in the boot command line. This attribute corresponds to the console
firmware environment variable with the same name. Set bootdef_dev only at the console prompt or by using the consvar utility.
SEE ALSO
Commands: consvar(8)
Others: sys_attrs(5)
System Administration
sys_attrs_bparm(5)