I have a T5240 with 7 LDOMS configured. One night, network comm was broken somehow. Nobody was doing anything on the machine at the time. Here is what I saw in messages:
So, it took down ALL of the interfaces (the entire quad card). It appears that it cannot allocate memory..... The funny thing is, I am not even using nxge3 - nothing is plugged into it, it has never been plumbed. I AM using nxge0,1,2 as aggr1 for vsw0. I shutdown the machine, pulled the power plugs and then booted.
After it came up, the network looked fine. The vsw0 was working properly. But, "svcs -a" reported the following problems:
So, I could not start my ldoms. Doing the following, resulted in such:
Also, about the same time, in dmesg output:
After a while poking around and such and running svcadm enable/restart, etc. We got the ldm and vntsd running again - independant of the service mgmt facility. It still shows them in maintenance mode.
I brought up all of the LDOMS successfully and it all seems to be running fine.
I am just not sure what started this whole thing. Now I am getting (where I was not getting them before):
Hi Folks,
Just a quick question - hopefully!
I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes... (3 Replies)
Hi !
I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before.
I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl.
... (2 Replies)
Hi Friends
we have sun T5240 server, we have taken ufsdump of this server remotely with scsi tapedrive, If we need to do ufsrestore means what we have to do, since T5240 has not having scsi port, any procedure is there?
Regards
Rajasekar (5 Replies)
Hi,
We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions.
RJS (4 Replies)
I tried using raidctl earlier today to use my 2 disks in a RAID1 setup and I totally destroyed my OS install. I'm sure I did something funky and it freaked out. No big deal...right?
This is what I was seeing after a reboot.
I decided to just reinstall the OS. It let me go through all of... (3 Replies)
its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on... (3 Replies)
Hello,
basically what this script is supposed to do is showing a list of hosts that is given a number, that you will be able to choose from a list.
A check is made to verify that the chosen number is within the array and this is where things go bad and I don't know why, bizarre.
I've spent... (5 Replies)
Setting up a T5240 with two disks c1t0d0 and c1t1d0.
I am trying to use raidctl but when I issue.
raidctl -l
I get
Controller 1
Disk: 0.0.0
Disk: 0.1.0
So I try
raidctl -c '0.0.0 0.1.0' -r 1 1
and I get "Array in use."
I try (4 Replies)
All,
After a power loss I went to power on our sun fire v120 that is running solaris 10 and now it will not boot. I tried power cycling it from the lom and pulling the cord but nothing works. All it does is after a power cycle it will start to boot and then start to spit out a bunch of hex... (2 Replies)