10 More Discussions You Might Find Interesting
1. IP Networking
I took over an M5000 and have a jumper server with a nic to connect to the console IP of an M5000. access via ssh user@ip.
it was working fine, another person can connect remotely on the subnet, but when I ssh,it just hangs and then times out.
so my question is,
any ideas of what I might... (4 Replies)
Discussion started by: rrodgers
4 Replies
2. Solaris
Hi All,
I have an Oracle M4000 server with Solaris 10 OS. I have access to Solaris root prompt.
But I don't know the XSCF IP of this server.
Is there any way to display XSCF IP from Solaris OS? (2 Replies)
Discussion started by: byrusber
2 Replies
3. Solaris
Hi all,
I understand SP is a separate processor use for management purposes.
I understand XSCF is the management facility (similar to IDRAC, ILOM etc).
I understand that we can create multiple domains in a SPARC machine (something like VM) and we can install OS in it.
I am able to use... (4 Replies)
Discussion started by: javanoob
4 Replies
4. Solaris
Hi
We have an M3000 single physical processor and 8gb of memory running Solaris 10. This system runs two Oracle Databases one on Oracle 9i and One on Oracle 10g.
As soon as the Oracle 10g database starts we see an immediate drop in system performance, for example opening an ssh session can... (6 Replies)
Discussion started by: gregsih
6 Replies
5. Emergency UNIX and Linux Support
Hi All,
I have SPARC T4-4 connected with XSCF console. By mistake console user name is set to "root" instead of "sunadmin" (This is what we keep as standard). How can I change it ? Please help me
-> show /SP/users/root
/SP/users/root
Targets:
ssh
Properties:
role... (1 Reply)
Discussion started by: solaris_1977
1 Replies
6. Emergency UNIX and Linux Support
we have a SUN M3000 server.
setup as only 1 domain.
disk c0t0d0 and c0t1d0 and setup as SVM mirrors.
a few days ago disk T1 failed.
new we have replaced the disk, but can's see the disk in format.
have done cfgadm and devfsadm.
still can't access the new disk in format.
the output... (6 Replies)
Discussion started by: robsonde
6 Replies
7. Solaris
Hi,
We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions.
RJS (4 Replies)
Discussion started by: rajasekg
4 Replies
8. Solaris
Hi, I was working on the M3000 and I did a init 0, powered off the system during the weekend. When I tried to poweron today, the XSCF linux boot image keeps on rebooting and does not go to the login for XSCF access. The "Check" LED is on amber. Tried diagnosing but cant get the system up. Any help... (1 Reply)
Discussion started by: incredible
1 Replies
9. Solaris
While entering to service mode on XSCF i getting following error
XSCF> service
Account is not enabled for service mode.
What could be the reason for this ? (5 Replies)
Discussion started by: fugitive
5 Replies
10. Solaris
is there a way to force an error on an xscf much the same way you can with logger on solaris 10? i would like to test and make sure setarchiving is appropriately configured. however, i do not want to just pull a power source as the system is in production. anyway have any insight? showarchiving... (0 Replies)
Discussion started by: pupp
0 Replies
bup-margin(1) General Commands Manual bup-margin(1)
NAME
bup-margin - figure out your deduplication safety margin
SYNOPSIS
bup margin [options...]
DESCRIPTION
bup margin iterates through all objects in your bup repository, calculating the largest number of prefix bits shared between any two
entries. This number, n, identifies the longest subset of SHA-1 you could use and still encounter a collision between your object ids.
For example, one system that was tested had a collection of 11 million objects (70 GB), and bup margin returned 45. That means a 46-bit
hash would be sufficient to avoid all collisions among that set of objects; each object in that repository could be uniquely identified by
its first 46 bits.
The number of bits needed seems to increase by about 1 or 2 for every doubling of the number of objects. Since SHA-1 hashes have 160 bits,
that leaves 115 bits of margin. Of course, because SHA-1 hashes are essentially random, it's theoretically possible to use many more bits
with far fewer objects.
If you're paranoid about the possibility of SHA-1 collisions, you can monitor your repository by running bup margin occasionally to see if
you're getting dangerously close to 160 bits.
OPTIONS
--predict
Guess the offset into each index file where a particular object will appear, and report the maximum deviation of the correct answer
from the guess. This is potentially useful for tuning an interpolation search algorithm.
--ignore-midx
don't use .midx files, use only .idx files. This is only really useful when used with --predict.
EXAMPLE
$ bup margin
Reading indexes: 100.00% (1612581/1612581), done.
40
40 matching prefix bits
1.94 bits per doubling
120 bits (61.86 doublings) remaining
4.19338e+18 times larger is possible
Everyone on earth could have 625878182 data sets
like yours, all in one repository, and we would
expect 1 object collision.
$ bup margin --predict
PackIdxList: using 1 index.
Reading indexes: 100.00% (1612581/1612581), done.
915 of 1612581 (0.057%)
SEE ALSO
bup-midx(1), bup-save(1)
BUP
Part of the bup(1) suite.
AUTHORS
Avery Pennarun <apenwarr@gmail.com>.
Bup unknown- bup-margin(1)