10 More Discussions You Might Find Interesting
1. Hardware
Hi All
I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command.
Following is the hardware RAID output.
root@oracledatabaseserver / $ raidctl
RAID Volume RAID RAID Disk... (0 Replies)
Discussion started by: Tirmazi
0 Replies
2. Solaris
hi all
when i trying to give auto-boot value as false as following
#eeprom auto-boot?=false
it is showing as
zsh: no matches found: auto-boot?=false
so felt this is because of error in hard ware so i tried this
#iostat -en
it is showing like
iostat -en
---- errors ---
s/w h/w trn... (4 Replies)
Discussion started by: wkbn86
4 Replies
3. Solaris
Hi All
I have a problem on T2000 server.
bash-3.00# uname -a
SunOS 5.10 aaa Generic_120011-14 sun4v sparc SUNW,Netra-T2000After the initial solaris installation server failed to boot:
Rebooting with command: boot
Boot device: disk:b File and args:
The file just loaded does not appear... (1 Reply)
Discussion started by: ouzist
1 Replies
4. Filesystems, Disks and Memory
I setup a RAID 5 with 5 drives, one failed, hardware failure so I physically removed it from the raid after powering the machine off then powered it back on and my raid was still good but no 5th drive. I built a 5th drive from scratch and added it in the raid thinking the raid would go into... (0 Replies)
Discussion started by: lacakid
0 Replies
5. Solaris
New to the boards here so please bear with me!
I have a T2000 server with Solaris 10 installed on it. Disk 0 is the only disk currently being used, as I do NOT have a RAID set up. Disk 1 is just sitting there looking pretty.
I'd like to set up a mirrored RAID in order to fully utilize both... (5 Replies)
Discussion started by: phi148
5 Replies
6. Solaris
Hi, a couple of T2000 servers did not show the component status and the output was too short. There was a patch that needed to be installed. I also updated to the latest recommended patch cluster and OBP patch.
After reboot/restart of picl, it worked ok for a couple of weeks. Then suddenly it went... (12 Replies)
Discussion started by: incredible
12 Replies
7. Solaris
Hi,
I have a root with hardware RAID on c0t0d0 and c0t2d0. I would like to set the boot device sequence in OBP for both hdds.
I have checked in ls -l /dev/rdsk/ for the path of c0t2d0 but it does not exist. Can anyone shed some lights on this?
AVAILABLE DISK SELECTIONS:
0.... (12 Replies)
Discussion started by: honmin
12 Replies
8. Solaris
Hi,
I have a netra t2000 running solaris 10. It is fully patched with the latest patch cluster and also patch 118833-36 and 126897-02. The SC sys_event level is set to 3.
I am running a test to show hardware log status, e.g simulating a power supply failure.Hence I unplug one of te... (3 Replies)
Discussion started by: ulemsee
3 Replies
9. Solaris
Hi everyone,
I am having a problem when running devfsadm. We have many T2000, but on one of them, that is connected to our SAN, devfsadm reports no new disks. If a reconfiguration reboot is done, the system reports the new disk. But only with a reboot. We have Solaris10 installed and Veritas... (13 Replies)
Discussion started by: jfotop
13 Replies
10. Solaris
Hello all
We've just bought a T2000. It has two disks and I'm trying to figure out how to create a mirror of the boot disk. I understand that I have to boot into single user mode from DVD and then use the raidctl command to set up the mirror and label the volume afterwards.
Format returns... (4 Replies)
Discussion started by: soliberus
4 Replies