Visit Our UNIX and Linux User Community


RAID Problem on SUSE 11.0


 
Thread Tools Search this Thread
Special Forums Hardware Filesystems, Disks and Memory RAID Problem on SUSE 11.0
# 1  
Old 10-17-2009
RAID Problem on SUSE 11.0

I setup a RAID 5 with 5 drives, one failed, hardware failure so I physically removed it from the raid after powering the machine off then powered it back on and my raid was still good but no 5th drive. I built a 5th drive from scratch and added it in the raid thinking the raid would go into recovery and add the new drive to replace the old one. It did do that BUT this is where I am at now: (sdb1 was the new one I added)

P.S. The /proc/mdstat file currently contains the following:

Personalities : [raid6] [raid5] [raid4]
md0 : active raid5 sda1[0] sdf1[5] sde1[3] sdd1[2] sdb1[6]
7813950976 blocks super 1.0 level 5, 128k chunk, algorithm 0 [5/4] [U_UUU]
[======================>] recovery =110.9% (1083725068/976743872) finish=3369970016313.0min speed=45615K/sec
bitmap: 102/466 pages [408KB], 2048KB chunk

unused devices: <none>

It is over 110% recovery and still going!!! What did I do wrong and can I stop it without destroying anything.

Thanks,
Tom

---------- Post updated at 05:45 PM ---------- Previous update was at 12:18 AM ----------

cat /proc/mdstat
Personalities : [raid6] [raid5] [raid4]
md0 : active raid5 sda1[0] sdf1[5] sde1[3] sdd1[2] sdb1[6]
7813950976 blocks super 1.0 level 5, 128k chunk, algorithm 0 [5/5] [UUUUU]
bitmap: 103/466 pages [412KB], 2048KB chunk
unused devices: <none>

Makes no sense to me I didn't know it could go over 100% in recovery Smilie

Thanks,
Tom

It's working fine now!

Previous Thread | Next Thread
Test Your Knowledge in Computers #323
Difficulty: Easy
In most programming languages, the operator ++ is equivalent to the statement -= 1;.
True or False?

10 More Discussions You Might Find Interesting

1. Hardware

Problem with External Raid Controller.

Hi, We have a Sunfire 4150 with On-Board Internal Raid Controller connected to 4 X 146 GB SAS disks. This also has an External Raid Controller (Storagetek Eight-Port, External HBA Model SG-XPCIESAS-R-EXT-Z) connected to a JBOD array ( Storagetek XTA2530 ) which has 5 X 300 GB Hard disk. ... (1 Reply)
Discussion started by: ranjansukumar
1 Replies

2. Solaris

Raid problem on T2000

Hi all, First post so be gentile :) It's my first time installing Solaris on T2000 server. I have 2 72GB HD's on it. After configuring HW raid and running raidctl command I get this output: bash-3.00# raidctl -l c0t0d0 Volume Size Stripe Status Cache RAID ... (2 Replies)
Discussion started by: Obi-Wan
2 Replies

3. Shell Programming and Scripting

RAID setup automation problem

Hi guys, I'm trying to write a small script that sets up RAID using MDADM without asking user for any input. Here's what I'm doing: start=`mdadm --create $2 --level=$3 --raid-devices=$4 $5 $6 << MAYDAY y MAYDAY` When I it, I get this ./redundancy -setup /dev/md0 1 2 /dev/files/test0... (3 Replies)
Discussion started by: alirezan
3 Replies

4. Solaris

Hardware Raid related problem

Dear All I would Like to know that if suppose c1t0d0 is of 72 gb hard disk and system boot from this hard disk and c1t1d0 is of 147gb hard disk. Can we implement hardware raid (Mirror) between these two hard disks of different capacity if raid crontroller is present in the server Kind regards (4 Replies)
Discussion started by: girish.batra
4 Replies

5. Filesystems, Disks and Memory

Problem replace disk with RAID-5 volumes

Good morning, I have a problem replacing a disk with raid-5 volumes. An hardware error was occurred from a disk c9t3 so all slices were in maintenace. Every slice is part of a raid-5 volume. Any replica is present. Following Volume manager manual for replacing a disk, I have: - phisically... (0 Replies)
Discussion started by: bonovox
0 Replies

6. Filesystems, Disks and Memory

Raid With Suse Linux

Hello i have a linux suse server and im having problems installing a highpoint rocket raid 2220 driver. The raid card is a pci card made buy highpoint tech on there web site they have the linux suse server driver i now have that driver on the desktop but dont know how to install it. The lunix... (0 Replies)
Discussion started by: Vaughan
0 Replies

7. Filesystems, Disks and Memory

IDE controlled / RAID card issue Suse 9.2

I just built a new box to run Suse, and I guess I shoud have spent more time researching the HCL. Anyway, the Promise RAID card I have will not work, and I am unable to install the OS. The only other IDE devide in the box is a DVDOM. I can only think of 2 options, but would appreciate some... (1 Reply)
Discussion started by: 98_1LE
1 Replies

8. UNIX for Dummies Questions & Answers

suse 9.0 problem video

i got a NV11 geForce2 100/200 and suse 9.0 pro boot the kernal but then the screen goes blank and nothing else can't install suse 9.0 pro and grabs for this problem x will not come up at all just the boot screen with rez and so on but once i tell it to install thats i have a nec multisync... (6 Replies)
Discussion started by: 3bumbs plumming
6 Replies

9. UNIX for Dummies Questions & Answers

SuSE 8.1 NIC problem

i have just installed suse 8.1 on a third computer which has an Asus p4s8x with onboard NIC and sound. now, on install suse detected everything automatically with no probelm, however upon reboot the sound failed to load as well as the network card. /dev/eth* doesnt exist. i looked in the bios and... (2 Replies)
Discussion started by: norsk hedensk
2 Replies

10. Filesystems, Disks and Memory

2-Ch RAID Problem in SCO Open Server

Help, if possible. In SCO Open Server with installation of two-channel RAID controller the following happens: on the channel 0 disk array is seen by an operational system, and on the channel 1 array is not seen (simultaneously). That is the operational system can not simultaneously use more than... (1 Reply)
Discussion started by: pko60
1 Replies

Featured Tech Videos