10 More Discussions You Might Find Interesting
1. AIX
Hello all,
I'm working to fix a two-node SysMirror cluster that uses NFS mounts from a NetApp appliance as the data repository. Currently all the NFS mounts/unmounts are called from the application controller scripts, and since file collection isn't currently working, (One fight at at time... (3 Replies)
Discussion started by: ZekesGarage
3 Replies
2. AIX
Hi all, I have the following in hacmp.out for bringing Resource group online.
Volume groups themselves are Enhanced-Capable and on each node I can varyon and mount filesystems.
+main1_rg_01:cl_activate_vgs STATUS=0
+main1_rg_01:cl_activate_vgs typeset -li STATUS
+main1_rg_01:cl_activate_vgs... (2 Replies)
Discussion started by: OdilPVC
2 Replies
3. AIX
Hello. I am Running AIX 6.1 and PowerHA 6.1
I have an active/active cluster (Prod/Dev) cluster. Each side will failover to the other.
I have on my prod side an active volume group with a file system. The VG is imported on both nodes and active (varried on, file system mounted) on the prod... (3 Replies)
Discussion started by: mhenryj
3 Replies
4. Solaris
hi, dear all
I get a problem "VCS ERROR V-16-2-13077 " on VCS 4.1 for Solaris 10.
I can not offline the host2 when the raid is bad.
I don't know the reason and how to offline host2 and switch to host1.
please help me, thank you!
the message of engine_A.log is :
... (2 Replies)
Discussion started by: ForgetChen
2 Replies
5. AIX
Hi,
I'm new to HACMP. Currently I setup a cluster with nfs cross-mount follow this guide:
kristijan.org NFS cross-mounts in PowerHA/HACMPMy cluster has two nodes: erp01 and erp02.
I'm using nfs4 with filesystem for nfs is: /sapnfs
Cluster start without problems. But I cannnot move RG (with... (3 Replies)
Discussion started by: giobuon
3 Replies
6. AIX
Hi,
I have a 2 node Cluster. Which is working in active/passive mode (i.e Node#1 is running and when it goes down the Node#2 takes over)
Now there's this requirement that we need a mount point say /test that should be available in active node #1 and when node #1 goes down and node#2 takes... (6 Replies)
Discussion started by: aixromeo
6 Replies
7. Solaris
Hi Admins,
I know that VCS supports Solaris x86-64bit only...and I need vcs for Solaris 32 bit-x86..running on vmware workstation.. I need to run vcs on vmware workstation...And my laptop support only 32bit... Please suggest..
Thanks.. (1 Reply)
Discussion started by: snchaudhari2
1 Replies
8. AIX
Hi,
Not sure if this is the correct forum to post this on but maybe a mod could move it if not.
When trying to move a HACMP resource group between lpars on AIX I receive the following.
State not STABLE/RP_RUNNING or ibcasts Join for node 2 rejected,
Clearing in join protocol flag... (11 Replies)
Discussion started by: elmesy
11 Replies
9. AIX
Hi,
I have a requirement to monitor the HACMP Resource Groups. At present in my environment, if the Resource Groups fail over from preferred node to Secondary node we dont get notification.
Can some one help me in creating a scrript. I have more than one RG online. (Max 4 Resource Groups in... (2 Replies)
Discussion started by: srnagu
2 Replies
10. High Performance Computing
I have rcently setup a 4 node cluster running sun cluster 3.2
and I have installed 4 zones on each node. when installing the zones I had to install the zone on all nodes the on the last node do a zlogin -C <zonename>
this worked ok.
theni I tried to siwitch the zone to node a thei work... (14 Replies)
Discussion started by: lesliek
14 Replies
clusvcadm(8) Red Hat Cluster Suite clusvcadm(8)
NAME
clusvcadm - Cluster User Service Administration Utility
SYNOPSIS
clusvcadm [-d <service> ] [-e <service> ] [-l] [-u] [-S] [-m <member> ] [-r <service> ] [-R <service> ] [-M <service> ] [-Z <service> ] [-U
<service> ] [-s <service> ] [-v]
DESCRIPTION
The clusvcadm command allows an administrator to enable, disable, relocate, and restart user services in a cluster. In order to perform
cluster service operations, the cluster daemons must be running (and have quorum) on the member system on which the command is invoked.
OPTIONS
-d <service>
Stops and disables the user service named service
-e <service>
Enables and starts the user service named service
-l Lock services in preparation for cluster shutdown. This should only be used if the administrator intends to perform a global, clus-
ter wide shutdown. This prevents services from starting (but not stopping, like -Z does). Once the cluster quorum is dissolved,
this state is reset. If a new instance of rgmanager boots while others are locked, the behavior is undefined.
-u Unlock resource group managers. This allows services to start again.
-S Display whether the resource group managers are locked or not. This can be used to verify the correct operation of the -l and -u
options, but is only useful for debugging.
-m <member>
When used in conjunction with either the -e or -r options, this specifies the preferred target member on which to start the service.
-r <service>
Relocates the user service named service to another cluster member.
-R <service>
Restarts the user service named service on the cluster member on which it is currently running.
-M <service>
Use a special "migration" operation to move the user service named service to another cluster member. Currently, this is only use-
ful for virtual machines. Use of migration usually requires special configuration of the local virtual machine manager in order to
work correctly.
-Z <service>
Freezes the service named service on the cluster member on which it is currently running. This will prevent status checks of the
service as well as failover in the event the node fails or rgmanager is stopped.
-U <service>
Unfreezes the user service named service on the cluster member on which it is currently running. This will re-enable status checks.
-s <service>
Stops the service named service until a member transition or until it is enabled again.
-v Display version information and exit.
NOTES
Executing -U (unfreeze) on a service which was frozen in the started state while the service owner is offline results in an undefined (and
possibly dangerous) condition. Manually ensure all resources are clear before doing this.
SEE ALSO
clustat(8)
Jan 2005 clusvcadm(8)