10 More Discussions You Might Find Interesting
1. Solaris
Now this doesnt look right to me. All of these disks are 100Gb LUNS so total zpool size is 300Gb.
Am I right in saying that this zpool consists of two disks plus one more disk that is 6 way mirrored?
So a bit pointless because only one of the three is mirrored (and 6 way is a bit of overkill... (3 Replies)
Discussion started by: psychocandy
3 Replies
2. Solaris
Hi all, I have a LUN that is in "Online Busy" when I issue the dev_gestate subcommand of luxadm:
root@es088wb6:~# luxadm -v -e dev_getstate /dev/rdsk/c21t50050763090887FEd4s2
phys path = "/devices/pci@6c0/pci@1/pci@0/pci@4/SUNW,qlc@0/fp@0,0/ssd@w50050763090887fe,4:c,raw"
... (5 Replies)
Discussion started by: ludiegu
5 Replies
3. Solaris
So,
We have a Netapp storage solution. We have Sparc T4-4s running with LDOMS and client zones in the LDOMS, We are using FC for storage comms. So here's the basic setup
FC luns are exported to the primary on the Sparc box. using LDM they are then exported to the LDOM using vdisk. at the... (4 Replies)
Discussion started by: os2mac
4 Replies
4. Solaris
I added a disk to a zpool using "zpool add diskname"
My intention was mirror a zpool disk that no mirror; that is a zpool with only one disk. I did not issue the right command. Now, the disk has been added successfully but I cannot remove nor detach it as Solaris 11 thinks it has data on it... (14 Replies)
Discussion started by: LittleLebowski
14 Replies
5. Solaris
So, we removed a LUN from the SAN and the system is refusing to remove the references to it in the /dev folder. I've done the following:
devfsadm -Cv
powermt -q
luxadm -e offline <drive path>
luxadm probe
All those commands failed to remove the path. The drive stills shows up as <drive... (13 Replies)
Discussion started by: DustinT
13 Replies
6. Solaris
Hi ,
One of my zone went down and when i booted it up i could see the pool in degraded state with some check sum errors . we have brought the pool online after scrubbing. But few files are showing this error
Bad exchange descriptor
Please let me know how to remove these files (2 Replies)
Discussion started by: chidori
2 Replies
7. UNIX for Advanced & Expert Users
Hi,
How to remove the allocate SAN Lun on the Linux Server. I am using rhel 5.8. I have assigned a LUN to the existing Volume group.
For eg: I have allocated a LUN with 20GB to the existing volume group(test123). Now, how can I take back the allocated lun without any issues. (1 Reply)
Discussion started by: gsiva
1 Replies
8. Solaris
hi ...
i have added a physical disk to the pool with
""zpool add <poolname> diskname"""... after that i realized that i have to mirror it instead..then i tried to take that disk out of the pool but i m not able to do that..
i have gone through many unix help sites , nothing worked ,
so please... (6 Replies)
Discussion started by: yrajendergoud
6 Replies
9. Solaris
I have a list of LUN ID, my task is to find if disk has been added or not. How do I do that? I have been searching the forum and not able to find answer.
thanks (4 Replies)
Discussion started by: uuontario
4 Replies
10. Solaris
I had a pool which was exported and due to some issues on my SAN i was never able to import it again. Can anyone tell me how can i destroy the exported pool to free up the LUN. I tried to create a new pool on the same pool but it gives me following error
# zpool create emcpool4 emcpower0c... (0 Replies)
Discussion started by: fugitive
0 Replies