10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi, I am faily new to linux and bash scripting. But essentially what I am trying to do is create a small bash script that will automatically install a driver I want. I can do it manually but I want to create a script so I won't forget, since it is an internet driver I won't be able to get help when... (0 Replies)
Discussion started by: dmacmillan
0 Replies
2. Programming
Hi, I am trying to write the simplest network driver that would send whatever through cable.
My configuration is:
Linux machine with some Intel network adapter
Another machine with WireShark
I connected Intel network adapter to second machine and want anything to pop up at wireshark.
... (12 Replies)
Discussion started by: Chrisdot
12 Replies
3. UNIX for Dummies Questions & Answers
Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean?
- It has to run on all network adapters
- It has to be as simple as it can be
- It has to run on all linux distributions (or at least most of them)
- It does not have to run a network... (4 Replies)
Discussion started by: Chrisdot
4 Replies
4. Solaris
I attached a README file that I will refer to.
I successfully completed everything in the README file until step 4.
# pwd
/gani/gani-2.4.4
# ls
COPYING Makefile.macros gem.c
Makefile Makefile.sparc_gcc gem.h
Makefile.amd64_gcc ... (1 Reply)
Discussion started by: Bradj47
1 Replies
5. Red Hat
I am using NVIDIA nforce: Networking controllers
And Redhat enterprice linux ws version 4 32 bit: OS
I want to connect my system to Broadband internet using linux.
From where can I download the driver for nertwork.
How to know whether the network driver alredy installed in my system.
... (0 Replies)
Discussion started by: rijas
0 Replies
6. Solaris
Hi All,
Just completing my second Solaris installation, in the previous one which was on a Dell X64 machine, I went through the Network configuration setting, on the current computer which I am installing Solaris on, its a custom built machine and for some reason, I didnt see the screen where I... (1 Reply)
Discussion started by: platforminc
1 Replies
7. Solaris
Hi ,
How to check the drivers of a dat tape? And once downloaded how to install drivers for the same??
Where to download drivers from? Having some trouble with Dat tape drive configuration.. (2 Replies)
Discussion started by: saurabh84g
2 Replies
8. Solaris
Hello all,
Needed a suggestion from you all, if you know anything about this stuff.
We have a high network traffic application. Close to around 700Meg /sec on one NIC.
When the traffic is around 200Meg on the NIC, the VCPU(not the CPU, cause we have 24 VCPU) utilization by the NIC driver... (5 Replies)
Discussion started by: Naanu
5 Replies
9. SCO
I have a new Dell PowerEdge 2900 with perc5/i and no os. I need to install SCO Openserver 6 and I need create a megasas BTLD floppy in order to install the os.
http://ftp.sco.com/pub/unixware7/714/drivers/megasas_1.1/README.hba.megasas.1.1.txt
According to the link, I need to download the... (4 Replies)
Discussion started by: jpop2000
4 Replies
10. Programming
HI,
I am writing a network device driver for RTL8139c card on 2.6.18 kernel ... I am facing few queries listed below
1. Can i able to at all write a driver for RTL8139C or Realtek had designed new chip for 2.6 series kernel?
2. If no then which driver file 2.6.18 uses .. Is it 8139too.c or... (1 Reply)
Discussion started by: niketan
1 Replies