9 More Discussions You Might Find Interesting
1. Solaris
I have a single zpool with 3 2-way mirrors ( 3 x 2 way vdevs) it has a degraded disk in mirror-2, I know I can suffer a single drive failure, but looking at this how many drive failures can this suffer before it is no good? On the face of it, I thought that I could lose a further 2 drives in each... (4 Replies)
Discussion started by: fishface
4 Replies
2. Solaris
All,
One-way mirror. Elements of the concat in Last-errd state. What would be the best way to correct it?
metastat -s db2test -pc
db2test/d220 p 5.0GB db2test/d200
db2test/d219 p 5.0GB db2test/d200
db2test/d218 p 5.0GB db2test/d200
db2test/d217 p 30GB db2test/d200... (0 Replies)
Discussion started by: ossupport55
0 Replies
3. Solaris
Hi Guys,
I need a help with attaching the sub mirrors as it keep throwing errors.
I have done solaris live upgrade and it was succesful but it keeps throwing error only for root (s0) and swap (s1)when i try to attach them.
For rest of the partitions for slices 3,4,5 on target 1 are able to... (4 Replies)
Discussion started by: phanidhar6039
4 Replies
4. Linux
Dear all,
CentOS 6
After executing "yum update -y" command I am facing this error. Please help me out.
thanks in advance. Full error & error code is given as follow:
... (7 Replies)
Discussion started by: saqlain.bashir
7 Replies
5. Linux
How can I add additional mirrors to my CENTOS distro, according to this page AdditionalResources/Repositories - CentOS Wiki there are few fedora project repositories I'd like to add any of them but I don't know how?
Thank you in advance (0 Replies)
Discussion started by: c0mrade
0 Replies
6. Solaris
Hi,
Ii am facing the belwo problem:
d50: Mirror
Submirror 0: d30
State: Needs maintenance
Submirror 1: d40
State: Needs maintenance
Pass: 1
Read option: roundrobin (default)
Write option: parallel (default)
Size: 212176648 blocks (101 GB)
d30:... (3 Replies)
Discussion started by: sag71155
3 Replies
7. Shell Programming and Scripting
hi
how floppy disks, CDs and flash drives (pen drives) are accessed in UNIX?
thanks (0 Replies)
Discussion started by: nokia1100
0 Replies
8. Solaris
Ok, so I have a remote system (7 states away) that's using SDS to manage the two 18 gig disks. /, swap, /var, /home, and /opt.
The mirroring procedure I created uses installboot to ensure there's a bootblk on both disks of an SDS mirror.
The system has a problem booting (can't write to... (21 Replies)
Discussion started by: BOFH
21 Replies
9. UNIX for Advanced & Expert Users
I am looking for the easiest and most generic way
to determine:
System model/class
Number of cpu's
Clock speed of cpu's (ie 550 MHz)
Total Physical Memory (not virtual)
Number of Drives/Drive Size
Thanks in advance, (4 Replies)
Discussion started by: eyounes
4 Replies
MLXCTL(8) BSD System Manager's Manual MLXCTL(8)
NAME
mlxctl -- Mylex DAC960 family management utility
SYNOPSIS
mlxctl [-f dev] [-v] [-a] status [drive] [...]
mlxctl [-f dev] [-a] detach [drive] [...]
mlxctl [-f dev] [-a] check [drive] [...]
mlxctl [-f dev] rebuild channel:target
mlxctl [-f dev] cstatus
mlxctl [-f dev] rescan
mlxctl [-f dev] config
DESCRIPTION
The mlxctl utility performs status monitoring and management functions for Mylex DAC960 RAID controllers and attached devices.
The following options are available:
-a Apply the action to all drives attached to the controller.
-f dev Specify the control device to use. The default is /dev/mlx0.
-v Increased verbosity.
The following commands are available:
cstatus Display the controller's current status.
status Display the status of the specified drives. This command returns 0 if all drives tested are online, 1 if one or more drives are
critical and 2 if one or more are offline.
rescan Re-scan the logical drive table, and attach or detach devices from the system as necessary.
detach Detach the specified drives. Drives must be unmounted and unopened for this command to succeed.
check Initiate a consistency check and repair pass on a drive that provides redundancy (e.g., RAID1 or RAID5). This command returns imme-
diately. The status command can be used to monitor the progress of the check.
rebuild Rebuild onto the specified physical drive. Note that there can be only one running rebuild operation per controller at any given
time. This command returns immediately. The cstatus command can be used to monitor the progress of the rebuild.
config Write the current system drive configuration to stdout.
EXAMPLES
Display the status of drive ld3 attached to the controller mlx1:
mlxctl -f /dev/mlx1 -v status ld3
SEE ALSO
ld(4), mlx(4)
HISTORY
The mlxctl command first appeared in NetBSD 1.5.3, and was based on the mlxcontrol utility found in FreeBSD.
BUGS
Modifying drive configuration is not yet supported.
Some commands do not work with older firmware revisions.
Error log extraction is not yet supported.
BSD
April 10, 2000 BSD