10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
say we have :
2914 | REQUEST | whatever
2914 | RESPONSE | whatever
2914 | SUCCESS | whatever
2985 | RESPONSE | whatever
2986 | REQUEST | whatever
2990 | REQUEST | whatever
2985 | RESPONSE | whatever
2996 | REQUEST | whatever
2010 | SUCCESS | whatever
2013 | REQUEST | whatever
2013 |... (7 Replies)
Discussion started by: Saumitra Pandey
7 Replies
2. Shell Programming and Scripting
Hi,
I have a file like below.
1,2,3,4,5,6,7,8,9I would like to print or copied to a file based of line count in perl
If I gave a condition 1 to 3 then it should iterate over above file and print 1 to 3 and then again 1 to 3 etc.
output should be
1,2,3
4,5,6
7,8,9 (10 Replies)
Discussion started by: Anjan1
10 Replies
3. Shell Programming and Scripting
Hello,
I want to extract from a file like :
20120530025502914 | REQUEST | whatever
20120530025502968 | RESPONSE | whatever
20120530025502985 | RESPONSE | whatever
20120530025502996 | REQUEST | whatever
20120530025503013 | REQUEST | whatever
20120530025503045 | RESPONSE | whatever
I want... (14 Replies)
Discussion started by: black_fender
14 Replies
4. Shell Programming and Scripting
I have a file that contains 87 lines, each with a set of coordinates (x & y). This file looks like:
1 200.3 -0.3
2 201.7 -0.32
...
87 200.2 -0.314
I have another file which contains data that was taken at certain of these 87 positions. i.e.:
37 125
42 175
86 142
where the first... (1 Reply)
Discussion started by: jackiev
1 Replies
5. Shell Programming and Scripting
Hello - First post here. I need help combining two lines that are non-consecutive in a file. Using sed, awk or perl preferably. So the file looks as follows. Please note, the "Line#:" is there only for reference. The lines can only be distinguished by whether they have "start" or "done" in... (2 Replies)
Discussion started by: munkee
2 Replies
6. Shell Programming and Scripting
Hi,
I search all forum, but I can not find solutions of my problem :(
I have multiple files (5000 files), inside there is this data :
FILE 1:
1195.921 -898.995 0.750312E-02-0.497526E-02 0.195382E-05 0.609417E-05
-2021.287 1305.479-0.819754E-02 0.107572E-01 0.313018E-05 0.885066E-05
... (15 Replies)
Discussion started by: guns
15 Replies
7. Shell Programming and Scripting
I have a file with ~200K lines, I need to delete 4K lines in it. There is no range.
I do have the line numbers of the lines which I want to be deleted.
I did tried using
> cat del.lines
sed '510d;12d;219d;......;3999d' file
> source del.lines
Word too long.
I even tried... (2 Replies)
Discussion started by: novice_man
2 Replies
8. Shell Programming and Scripting
The symbols are \t and \t\t (note: not tab)
If the line starts with \t merge them into a single line upto symbol \t\t
\t\t to end and start new line
I able to join in a single line but not ending at \t\t and I completely confused
help would be appreciated:b::D
Input
\ta tab XXXXXXXXXX
\te... (5 Replies)
Discussion started by: repinementer
5 Replies
9. UNIX for Dummies Questions & Answers
Hi All,
I want to merge two consecutive lines.
Currently the output is :-->
crmplp1 cmis461 No Online
cmis462 No Offline
crmplp2 cmis462 No Online
cmis463 No ... (6 Replies)
Discussion started by: pank29
6 Replies
10. Shell Programming and Scripting
Dear friends, Please help me to resolve the problem below,
I have a file with following content:
date of file creation : 12 feb 2007
====================
= name : suresh
= city :mumbai
#this is a blank line
= date : 1st Nov 2005
====================
few lines of some text
this... (7 Replies)
Discussion started by: swamymns
7 Replies
GIT-MERGE-FILE(1) Git Manual GIT-MERGE-FILE(1)
NAME
git-merge-file - Run a three-way file merge
SYNOPSIS
git merge-file [-L <current-name> [-L <base-name> [-L <other-name>]]]
[--ours|--theirs|--union] [-p|--stdout] [-q|--quiet] [--marker-size=<n>]
<current-file> <base-file> <other-file>
DESCRIPTION
git merge-file incorporates all changes that lead from the <base-file> to <other-file> into <current-file>. The result ordinarily goes into
<current-file>. git merge-file is useful for combining separate changes to an original. Suppose <base-file> is the original, and both
<current-file> and <other-file> are modifications of <base-file>, then git merge-file combines both changes.
A conflict occurs if both <current-file> and <other-file> have changes in a common segment of lines. If a conflict is found, git merge-file
normally outputs a warning and brackets the conflict with lines containing <<<<<<< and >>>>>>> markers. A typical conflict will look like
this:
<<<<<<< A
lines in file A
=======
lines in file B
>>>>>>> B
If there are conflicts, the user should edit the result and delete one of the alternatives. When --ours, --theirs, or --union option is in
effect, however, these conflicts are resolved favouring lines from <current-file>, lines from <other-file>, or lines from both
respectively. The length of the conflict markers can be given with the --marker-size option.
The exit value of this program is negative on error, and the number of conflicts otherwise. If the merge was clean, the exit value is 0.
git merge-file is designed to be a minimal clone of RCS merge; that is, it implements all of RCS merge's functionality which is needed by
git(1).
OPTIONS
-L <label>
This option may be given up to three times, and specifies labels to be used in place of the corresponding file names in conflict
reports. That is, git merge-file -L x -L y -L z a b c generates output that looks like it came from files x, y and z instead of from
files a, b and c.
-p
Send results to standard output instead of overwriting <current-file>.
-q
Quiet; do not warn about conflicts.
--ours, --theirs, --union
Instead of leaving conflicts in the file, resolve conflicts favouring our (or their or both) side of the lines.
EXAMPLES
git merge-file README.my README README.upstream
combines the changes of README.my and README.upstream since README, tries to merge them and writes the result into README.my.
git merge-file -L a -L b -L c tmp/a123 tmp/b234 tmp/c345
merges tmp/a123 and tmp/c345 with the base tmp/b234, but uses labels a and c instead of tmp/a123 and tmp/c345.
GIT
Part of the git(1) suite
Git 1.8.3.1 06/10/2014 GIT-MERGE-FILE(1)