10 More Discussions You Might Find Interesting
1. AIX
Does AIX (or even the ASMI interface) provide a method to obtain basic data from a SFP+ (aka 10Gb transceiver) installed in a NIC card ?
In this case, the machine is remote (to me), a Power8, with EN0S adapter (2 x 10GbE and 2 x 1Gb).
Specifically, just trying to determine basic things from... (2 Replies)
Discussion started by: The Doctor
2 Replies
2. Solaris
Hi there,
In Solaris 8.
I have accidentally set the eeprom security-mode=command because I followed the CIS benchmark guideline. Initally, it was eeprom security-mode=none. I have tried to login with the correct password numerous time and it still say permission denied.
I have tried to login... (4 Replies)
Discussion started by: alvinoo
4 Replies
3. UNIX for Dummies Questions & Answers
Hi,
I need to get an output that is the same as "ethtool -e eth0"
But I need to use another method that does not use the eth port ID (ethX).
Does anyone know of any method?
Thanks!! (3 Replies)
Discussion started by: h0ujun
3 Replies
4. UNIX for Advanced & Expert Users
Hello all,
I am currently trying to find a solution to replacing some 10 year old Solaris boxes because it is obvious that they are going to fail soon. The problem is that they are license servers, and I need the eeprom serial to transfer to a new computer. Now, I could request that we get new... (1 Reply)
Discussion started by: DeanCarlo
1 Replies
5. Shell Programming and Scripting
Hi all,
So I have a binary file and I need to generate an expected EEPROM checksum for it. Ideally, I would like to input the file (with the path) and output a computed checksum. Ive been using (cksum file1) with no avail and I was just curious as to whether there is such thing as EEPROM cksum,... (1 Reply)
Discussion started by: TeamUSA
1 Replies
6. UNIX for Dummies Questions & Answers
Hi all,
So I have a binary file and I need to generate an expected EEPROM checksum for it. Ideally, I would like to input the file (with the path) and output a computed checksum. Ive been using (cksum file1) with no avail and I was just curious as to whether there is such thing as EEPROM... (1 Reply)
Discussion started by: TeamUSA
1 Replies
7. Solaris
Hi ,
Am new to solaris can anyone tell me what is the use of setting the eeprom variable to true or false ... (5 Replies)
Discussion started by: rogerben
5 Replies
8. UNIX for Advanced & Expert Users
hello
i have sun machine and i need to reset EEPROM password where evrytime machine boot i should put password to start in booting
any one can help me how i can remove this password
Thanks (1 Reply)
Discussion started by: asafwat
1 Replies
9. Solaris
Hi Guys,
There was a post that I saw here a while ago regarding file system layout and what to put where, which I am unable to find now..
A user here posted a man page that list what each partition should have in it and what it is used for and were you should install custom packages.
ie:... (1 Reply)
Discussion started by: Tornado
1 Replies
10. UNIX for Advanced & Expert Users
Hi: I was setting up a modem on an Ultra5 running 2.6. (yes I know, how quaint)
There are 15 systems that are interlinked but not accessible to the outside world.
This will end soon with new updated sun systems but until then the system needs to be accessed by the outside world. Hence the... (1 Reply)
Discussion started by: mndavies
1 Replies
EEP24C(1) General Commands Manual EEP24C(1)
NAME
eep24c - read and write 24Cxxx eeprom devices
SYNOPSIS
eep24c -d device [ -r[n] filename | -w[n] filename | -k[n] filename | -f[n] xx ]
DESCRIPTION
The command eep24c can be used to read and write 24Cxxx eeprom devices.
OPTIONS
The following options are available:
-d device
Specify the device type. To see a list of the supported devices, try -d help
-r filename
Read from eeprom and save to a file.
-w filename
Read from a file and write to eeprom. The addresses not specified in the input file will be filled with 00.
-k filename
Read from a file and write to eeprom. The addresses not specified in the input file will be kept with its previous values. (this
mode is twice slower. It reads whole memory to know previous values, then write whole memory)
-f XX Fills the whole eeprom with XX (XX is an hexadecimal value)
n Can be used to multiply clock time. If you have a long cable, you may use this option. Example: -r5 will read eeprom 5 times slower
(pulse width will be standard value multiplied by 5). Valid range for n is from 1 to 50. Default value is 1.
USAGE EXAMPLES
eep24c -d 24c04 -r file.hex
read eeprom, write to file.hex
eep24c -d 24c04 -r3 file.hex
read eeprom, write to file.hex, 3 times slower.
eep24c -d 24c04 -w file.hex
read file.hex and write to eeprom. All the bytes not found in file.hex will be written as 00.
eep24c -d 24c04 -k file.hex
read file.hex and write to eeprom. All the bytes not found in file.hex will remain unchanged.
eep24c -d 24c04 -f 7A
fill eeprom with 7A (hexadecimal).
INPUT AND OUTPUT FORMAT
Input and output file format is Intel Hexadecimal Object File Format
You can find this specification at
ftp://download.intel.com/support/processors/
i960/devtools/INTELHEX.PDF
Record types 00 and 01 are implemented in this version. In input lines, LF and CR+LF are accepted as newline markers. Output files are
generated with LF as a newline marker.
DEVICE SPECIFIC
If you are using Microchip 24*515, you must tie its pin A2 to VCC (needs a hardware modification, see device datasheet).
SEE ALSO
ihex2txt(1), txt2ihex(1).
AUTHOR
This manual page was written by Pedro Zorzenon Neto <pzn@vztech.com.br>.
2002-11-14 EEP24C(1)