10 More Discussions You Might Find Interesting
1. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
2. SCO
hi
i installed sco unix open server 5.0.7 on virtual machine vmware and runing it,
its work perfect and good.
now how i can configuare network at scoadmin that i able to access nework ?
---------- Post updated at 08:56 AM ---------- Previous update was at 01:47 AM ----------
nobody can... (2 Replies)
Discussion started by: farzad226
2 Replies
3. UNIX for Dummies Questions & Answers
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Discussion started by: flashinwrx
8 Replies
4. UNIX for Dummies Questions & Answers
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies
5. AIX
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies
6. AIX
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
Discussion started by: ariec
1 Replies
7. SCO
Hello Guys,
We have an old PC running on SCO Unix V. Is there any sites where i can get manual/procedures on how to install and configure Network. Thanks (2 Replies)
Discussion started by: nrcuevas
2 Replies
8. AIX
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies
9. SCO
I have got a Sco Unix Server, i want to connect some windows workstations. What configurations do i need to make on server and or workstation? (1 Reply)
Discussion started by: tpurazi1
1 Replies
10. UNIX for Dummies Questions & Answers
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
Discussion started by: potter
1 Replies
IFPORT(8) System Manager's Manual IFPORT(8)
NAME
ifport - select the transceiver type for a network interface
SYNOPSIS
ifport interface [auto|10baseT|10base2|aui|100baseT|##]
DESCRIPTION
Ifport sets the transceiver type for the specified network interface, for drivers that support multiple transceiver types. If a type is
not specified on the command line, then the current type is displayed. The type can be specified either numerically or by keyword. The
five standard transceiver types (auto, 10baseT, 10base2, aui, and 100baseT) correspond to codes 0 to 3, for all the Linux PCMCIA network
drivers. The keyword match is case insensitive.
The network drivers may not reconfigure a card for a new transceiver type if the interface is already open. It is best to invoke ifport
prior to configuring the interface with ifconfig to ensure that the new setting takes effect immediately.
This utility only works with a limited set of 16-bit PC Card drivers: 3c589_cs, nmclan_cs, pcnet_cs, smc91c92_cs, and xirc2ps_cs. If
invoked for other drivers, ifport may report bogus transceiver settings, or report ``Operation not supported''.
DIAGNOSTICS
ioctl: Operation not supported
Indicates that this network device does not support manual transceiver selection. There may be only one transceiver option, or the
device may always autodetect the appropriate transceiver.
AUTHOR
David Hinds - dahinds@users.sourceforge.net
SEE ALSO
ifconfig(8).
pcmcia-cs 2000/06/12 21:24:48 IFPORT(8)