10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
I have issue with the perl module installed in the new Linux server
I have installed the required module, but still the perl program was not able to find the path
I'm getting the below error:
Can't locate Log/Log4perl.pm in @INC (@INC contains: /usr/lib/perl5/site_perl/Log4perl.pm... (5 Replies)
Discussion started by: help_scr_seeker
5 Replies
2. Linux
Hi,
I am using Red Hat 9.0 and it does not have the inbuilt driver module for my onboard lan card (RTL 8169). I downloaded the module (file - r8169-6.017.00.tar.bz2 and even r8169-6.015.00.tar.bz2), but when try to install it it says r8169.h , r8169_n.c , Makefile etc are... (2 Replies)
Discussion started by: dextergenious
2 Replies
3. Shell Programming and Scripting
Hi 'm getting error while installing perl mdule on linux.can any one tell me how to resolve that error?
problem is:
CPAN: File::Temp loaded ok (v0.22)
CPAN.pm: Going to build J/JD/JDB/Win32-OLE-0.1709.tar.gz
OS unsupported
Warning: No success on command
Warning (usually harmless):... (1 Reply)
Discussion started by: kavi.mogu
1 Replies
4. Windows & DOS: Issues & Discussions
Hi,
I am struggling in installing TK module for strawberry perl.
I downloaded TK804 module,
extracted to a folder, kept in c:/strawberry/perl/lib path,
then from tht path
1) perl makefile.pl
2)dmake
3)dmake test
4)dmake install
During perl makefile.pl it is giving error as... (3 Replies)
Discussion started by: vasanth.vadalur
3 Replies
5. Solaris
I have installed Solaris 10 in my PC successfully and my system having Intel(R) PRO/100 VE ethernet card. Solaris OS not able to detect the network card. So i checked the driver (INTCGigaE) and reinstalled. Still network card is not detected.
bash-3.00# pkgchk INTCGigaE
ERROR:... (0 Replies)
Discussion started by: paventhan
0 Replies
6. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
7. Shell Programming and Scripting
Hi All,
I am failry new to Perl.I am trying to install a Perl module (Filesys::df.pm) in an IBM AIX5.3 server.But I could not succeed in that.I am getting the following error:
abcd3dev# make
cc_r -c -D_ALL_SOURCE -D_ANSI_C_SOURCE -D_POSIX_SOURCE -qmaxmem=16384 -qnoansialias... (6 Replies)
Discussion started by: surjithss
6 Replies
8. UNIX for Advanced & Expert Users
Hi,
I am trying to install perl modules in HPUX under my account. I do not have the root permission.
The module name I am trying to install is Spreadsheet-WriteExcel. I have downloaded the tar.gz file from CPAN and extracted the same under my home directory.
When I try do 'perl... (2 Replies)
Discussion started by: sabyasm
2 Replies
9. Solaris
hello solaris friends,
I've tried installing Sun Solaris 10.0, but everytime it seems to bypass the network config. screen that looks similar to this...here's the url:
http://www.hup.hu/old/images/hup/Solaris/Sol10beta7/9.png
I'm able to install it all the way through but I get no... (2 Replies)
Discussion started by: cadmiumgreen
2 Replies
10. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
DUMMY_CS(4) Kernel Interfaces Manual DUMMY_CS(4)
NAME
dummy_cs - PCMCIA dummy device driver
SYNOPSIS
insmod dummy_cs.o [pc_debug=n] [free_ports=n] [irq_list=i,j,...]
DESCRIPTION
The dummy_cs module has two purposes. It is intended as a demonstration of how to write the PCMCIA interface code for a client driver, and
the source code is heavily commented. It is also written to function as a sort of generic ``point enabler'': when bound to any PCMCIA IO
card, it will read the card's Configuration Information Structure, and configure the card appropriately. The configuration includes set-
ting up IO and memory windows, configuring the card for interrupts, and initializing the card's PCMCIA configuration registers.
It turns out that many cards report incomplete or inaccurate configuration information, due to vendor carelessness and the complexity of
the data format. A vendor driver can generally take for granted many configuration details, so there is not much incentive for vendors to
ensure that the on-card information is complete. Thus, the dummy_cs module is limited by its generality: since it makes no assumptions
about card types, it is forced to rely on the card information, for better or worse.
PARAMETERS
pc_debug=n
Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero
value enables debugging.
free_ports=n
A flag indicating if the IO ports allocated for the card should be freed from the kernel resource maps. This is useful if the dummy
driver is being used to configure a card in preparation for loading a specific PCMCIA-unaware driver. The default is 0 (false).
irq_list=i,j,...
Specifies the set of interrupts that may be allocated by this driver.
AUTHOR
David Hinds - dahinds@users.sourceforge.net
SEE ALSO
cardmgr(8), pcmcia(5).
pcmcia-cs 2000/06/12 21:24:47 DUMMY_CS(4)