10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
I am working on an Urdu to Hindi dictionary and I have created the following file structure:
Headword=Gloss1,Gloss2,Gloss3
i.e. glosses delimited by a comma.
It so happens that in some cases (around 6000+ in a file of over 200,000+ the glosses are duplicated.
Since this may be a... (3 Replies)
Discussion started by: gimley
3 Replies
2. Linux
Hi All,
I am booting by Linux box with the run level 3 and it gets booted successfully.
I want to execute a script once the system is up and running in the run level 3. I was trying to add a entry to /etc/inittab to execute my script once the system is up.
I have added the below... (5 Replies)
Discussion started by: kalpeer
5 Replies
3. Shell Programming and Scripting
Hi
Im trying to scan a file for certain entries and remove their corresponding lines completely. What I have now is this,
for USER in user1 user2 user3 user4
do
sed '/$USER/d' /etc/sudoers
done
However this doesn't remove the entries at all. Is there another way for this?
Thanks... (2 Replies)
Discussion started by: bludhemn
2 Replies
4. Shell Programming and Scripting
Hi,
I need to delete duplicate records in a file that is around 30MB. Below is what I need. Below are the entries of input file and the output file that I need. Each section of input file is separated by an empty line. Some of these sections have duplicate uid values. I want to retain only one... (4 Replies)
Discussion started by: Samingla
4 Replies
5. Shell Programming and Scripting
Hello everyone,
I want to compare the first line of a file(ABC) with that of a folder,XYZ(folder contents) and want that line to be deleted from the file(ABC) if that entry doesn't exist in the folder(XYZ)
I want to put this in a loop. please can anyone help
thanks (6 Replies)
Discussion started by: swasid
6 Replies
6. Solaris
Hi,
I have a solaris 10 server,which has a process running that communicates with other system.I have made following entry in the inittab file.
PM15:s12345:respawn:/ncm/bin/communicator
PM15 : Unique process ID
s12345 : run levels
respawn : if anytime the process... (2 Replies)
Discussion started by: asalman.qazi
2 Replies
7. HP-UX
Hi relatively new to unix so sorry if this is a stupid question:
How do i add a printer entry into the host file.
I know how to add the printer using sam, but i am required to add the host file entry into /etc/hosts which i am unaware of how to do.
Any help would be greatly appreciated. (2 Replies)
Discussion started by: Wade Gava
2 Replies
8. Shell Programming and Scripting
I have written this small script to add an entry to a remote /etc/hosts file which needs to be run from our central admin box and is passed one parameter $1 <hostname>
#!/bin/ksh
echo "Which host entry would you like to add to $1"
read host_to_add
echo "what is the IP address?"
read ip
... (4 Replies)
Discussion started by: hcclnoodles
4 Replies
9. Shell Programming and Scripting
Hi falks,
I have the following ksh function ,which adding entry to crontab during ksh program running:
{
print "Go\c" >/dev/null 2>&1
print '0 0 * * * su - ias -c "/home/orca/core-${SCHEMA_NAME}/CLI/cleanup_BRMS.ksh"\c' >/dev/null 2>&1
print "\033:wq!" >/dev/null 2>&1
} | \crontab -e... (2 Replies)
Discussion started by: nir_s
2 Replies
10. Shell Programming and Scripting
Hi,
I am having almost the same problem as junior member 'oupsforum' (refer to subjuct "deleting double entry in a log file"), only that I am using Sun Sorlaris Unix which the uniq command does not has the flag -w. So I am not able to ignore certain portion of the line when the uniq doing the... (3 Replies)
Discussion started by: Wing m. Cheng
3 Replies
inittab(4) Kernel Interfaces Manual inittab(4)
NAME
inittab - Controls the initialization process
SYNOPSIS
/etc/inittab
DESCRIPTION
The inittab file provides the init program with instructions for creating and running initialization processes. The init program reads the
inittab file each time init is invoked. The file typically contains instructions for the default initialization, the creation and control
of processes at each run level, and the getty command, which controls the activation of terminal lines.
Each line in the inittab file contains an entry that has four fields; each field is separated by a colon. There is no limit to the number
of entries in the inittab file. The entry syntax is as follows: Identifier:Runlevel:Action:Command
Specifies a fourteen character field used to uniquely identify an object. Specifies a twenty character field that defines the run levels
in which the object is to be processed. Runlevel corresponds to a configuration of processes in a system. Each process spawned by the init
command is assigned one or more run levels in which it is allowed to exist. The run levels are as follows: Specifies the halt state.
Specifies multiuser state without network services. Specifies multiuser state with network services. Specifies single-user state. You
can define multiple run levels for a process by specifying more than one run level character in any combination. Specifies a twenty char-
acter field that tells init how to treat the specified process. init recognizes the following Action values: Specifies that if the process
does not exist or if it dies, init starts it. If the process exists, init continues to process the inittab file. Specifies that if init
enters a run level that matches the run level specified in the inittab file entry, it starts the process and waits for its termination. As
long as init continues in this run level, it does not act on subsequent reads of the entry in the inittab file. Specifies that if init
enters a run level that matches the run level specified in the inittab file, it starts the process and does not wait for its termination.
When the process stops, init does not restart it. If init enters a new run level where the process is still running from a previous run-
level change, init does not restart the process. Specifies that when init first executes and reads the inittab file, it processes this
entry. The init program starts the process and does not wait for its termination. When the process stops, init does not restart it. The
run level specified in this inittab file entry should be the default run level, or it must match the run level in which init operates at
boot time. Specifies that when init first executes and reads the inittab file, it processes this inittab file entry. The init program
starts the process, waits for its termination and, when it dies, does not restart the process. (This value exists only for SVID3/SVR4 com-
patibility.) Specifies that if init receives the SIGPWR power fail signal, it executes the process associated with this line. (This value
exists only for SVID3/SVR4 compatibility.) Specifies that if init receives the SIGPWR power fail signal, it executes the process associ-
ated with this line and waits until the process terminates before continuing processing the inittab file. Specifies that if the process
associated with this line is currently running, init sends the warning signal SIGTERM and waits 20 seconds before sending the kill signal
SIGKILL. If the process does not existent, init ignores the inittab entry. Specifies that a line with this action is processed when init
is originally invoked. The init program uses this line to determine the run level to enter originally. It determines this by taking the
highest run level specified in the run level field and using that as its initial state. If the run level field is empty, this is inter-
preted as 0s23, causing init to enter run level 3. If init does not find an initdefault entry in the inittab file, it requests an initial
run level from the operator. Specifies that entries of this type are executed before init tries to access the console. This inittab file
entry should be used only to initialize devices on which init could attempt to request a run level. Specifies a 1024 character field that
contains the sh command to be executed. The command is prefixed with exec. Any legitimate sh syntax can appear in the command field. Com-
ments can be inserted be specifying a number sign (#). The line continuation character can be placed at the end of a line.
EXAMPLES
The following is an example of an inittab file entry for a terminal line: tty01:23:respawn:/usr/sbin/getty /dev/tty08 9600 vt100
FILES
Specifies the command that initializes and controls terminal lines.
RELATED INFORMATION
Commands: init(8), getty(8)
Functions: kill(2) delim off
inittab(4)