serial port reading

9 More Discussions You Might Find Interesting

1. Solaris

Cabling and adapters to communicate to service processor serial port from Windows PC with USB port.

Hello, I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build. The first part is what confuses me -the cabling. I am coming from a Windows machine (w/appropriate...

2. Debian

Reading data from a serial port

Dear List - I am trying to capture data from a serial port and write it to a file. /var/www$ cat /dev/ttyS0 > scale_value.html cat: /dev/ttyS0: Device or resource busy /var/www# cat /proc/tty/driver/serial serinfo:1.0 driver revision: 0: uart:16550A port:000003F8 irq:4 tx:90...

3. Shell Programming and Scripting

reading from and writing to serial port

hello all, please any one can provide me the shell script to write data to /dev/ttyS1 and read responce from /dev/ttyS1 and compare the responce to some string .. thnxx ---------- Post updated at 03:35 PM ---------- Previous update was at 11:46 AM ---------- any body help me.. how do i...

4. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected...

5. Shell Programming and Scripting

Need help with serial port

Hi, I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and...

6. Programming

Serial port programming

I am developing an application in c with Linux OS, where a radio modem working at baud rate 9600 will be attached to PC on serial port. More than four such units will be communicating at one time, so there may be jamming or data corruption. Each module will be transmitting Data packets less than...

7. Linux

Urgent - serial port

Hi All, I am a begineer in Linux, I have 4 ports and 3 are operational port 1,port 2 and port 4 (when I plug in serial device I can see it working) but port 3 seems it is not working. I am sure the hardware is fine. when I give command dmesg | grep tty I get, serial 8250:ttyS0 at...

8. SCO

Serial port configuration

Hi I have just re-installed Compaq ML350 G2 Server with Unix SCO 5.0.5 and informix DBMS . on this server we have 2 serial ports , unfortunately its not working. Can anyone help me to check the serial ports working or not OR guide me to reconfigure it. I have attached a device with...

9. UNIX for Advanced & Expert Users

Communicating with Serial Port

I am using system running on red hat linux 4. I had connected health measuring machine to the serial port and configured it stty -F /dev/ttyS0 9600 -parenb cs8 -cstopb this machine requires a command to be passed to it for giving output. I am unable to pass command hexa format(0x68) to the...

LEARN ABOUT DEBIAN

reader.conf

READER.CONF(5)							    PC/SC Lite							    READER.CONF(5)

NAME

       reader.conf - configuration file for pcscd readers' drivers

DESCRIPTION

       The /etc/reader.conf.d/reader.conf file contains configuration information for serial and (some) PCMCIA smart card readers.

       USB readers SHALL NOT be configured using this file.  pcscd uses another mechanism to automatically load USB drivers.

SYNTAX

       The /etc/reader.conf.d/reader.conf is a regular text file. Each reader must be defined by four fields:

	FRIENDLYNAME	 TEXT_STRING
	DEVICENAME	 FILENAME
	LIBPATH 	 FILENAME
	CHANNELID	 NUMBER

       The "FRIENDLYNAME" field is an arbitrary text used to identify the reader. This text is displayed by commands like pcsc_scan(1) that prints
       the names of all the connected and detected readers.

       The "DEVICENAME" field was not used for old drivers (using the IFD handler version 2.0 or earlier). It is now  (IFD  handler  version  3.0)
       used  to  identify the physical port on which the reader is connected. This is the device name of this port. It is dependent of the OS ker-
       nel. The first serial port device is called /dev/ttyS0 under Linux and /dev/cuaa0 under FreeBSD.

       The "LIBPATH" field is the filename of the driver code. The driver is a dynamically loaded piece of code (generally a drivername.so*file).

       The "CHANNELID" is no more used for recent drivers (IFD handler 3.0) and has been superseded by "DEVICENAME". If you  have  an  old  driver
       this  field  is	used  to  indicate  the port to use. You should read your driver documentation to know what information is needed here. It
       should be the serial port number for a serial reader.

EXAMPLE

	# Gemplus GemPCTwin reader with serial communication
	# connected to the first serial port
	FRIENDLYNAME	  "GemPCTwin serial"
	DEVICENAME	  /dev/ttyS0
	LIBPATH 	  /usr/lib/pcsc/drivers/serial/libccidtwin.so.0.4.1
	CHANNELID	  1

DEBUGGING

       In order to set up your /etc/reader.conf.d/reader.conf file correctly you may want to have debug messages from pcscd.  I recommend  you	to
       start pscsd in the foreground and debug mode using:
	# pcscd --foreground --debug

       If  everything  seems  OK  you can use the pcsc_scan command to print the list of correctly detected readers and try to get the ATR of your
       smart cards.

AUTHOR

       Ludovic Rousseau <ludovic.rousseau@free.fr>

SEE ALSO

       pcscd(8), pcsc_scan(1)

Muscle								    August 2005 						    READER.CONF(5)

Programming