10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
I'm new to Linux (Ubuntu 16.04), and very new to BASH scripting. I have a Numato 8-channel USB GPIO device, which is a DAQ that appears in the system as a serial port. In Linux it appears as ttyACM0. I can easily manipulate a GPO with, for example:
echo "gpio set 7" > /dev/ttyACM0
...followed... (12 Replies)
Discussion started by: Chalk-X
12 Replies
2. Programming
Hi
I try to communicate with a GSM modem, from C, for sending SMS.
I use standart AT-commands.
Working well with terminal.
There is no problem writing ti the port.
But when I try to read I only get a echo, I write "ATI" and get "ATI" back, I should get somthing like "SIEMENS 35... (4 Replies)
Discussion started by: dmiller
4 Replies
3. Programming
hi, I've a problem on my C/C++ program with Posix Library.
I have to read data from the serial but I have incorrect data, in fact I get a bunch of zeros:
"2953.3174, 2785.2126, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0 , 0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0, 0.0 ,... (24 Replies)
Discussion started by: enaud
24 Replies
4. SCO
I am trying to change one of my serial printers from /dev/ttyr002 to /dev/ttyr014:
lpstat -s
device for check3: /dev/ttyr002
device for check4: /dev/ttyr002
I changed the tty setting for check3 in:
/etc/printcap
/var/spool/lp/admins/lp/printers/check3
to /dev/ttyr014
Then I get:... (4 Replies)
Discussion started by: herot
4 Replies
5. AIX
Hi Everyone,
The machine I'm working on is an AIX 5.3 LPAR running on a P650. oslevel -r shows 5300-08. I'm trying to take a backup to a SCSI tape drive, which has been working up until this point. I know of nothing that has changed recently to cause this problem. But when I try to take a... (0 Replies)
Discussion started by: need2bageek
0 Replies
6. Shell Programming and Scripting
My input is a long list of data start with "#":
#read_1
123456898787987
#read_2
54645646540646406
#read_3
4654564654316
.
.
I got a bit confusing about how to set all in an array first. And then when I run a program name "statistic_program", it will read the array in scalar and do... (24 Replies)
Discussion started by: patrick87
24 Replies
7. Ubuntu
Hello!
I am working on an application which reads environmental instruments which have serial ports. The application requires a serial port to be present to talk to the device (i.e. /dev/ttyS0 ). In some instances the environmental devices will be 100's of yards away from the computer, so a... (5 Replies)
Discussion started by: mvona
5 Replies
8. Linux
Hey!
I'm trying to figure out a sollution for a problem I have at my company with an Iomega MiniMax 500 GB USB disk.
If i run cat /proc/bus/usb/devices
I get this information:
T: Bus=01 Lev=02 Prnt=04 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00... (2 Replies)
Discussion started by: noratx
2 Replies
9. Programming
I am trying to access DG-100 gps logger on Mac OS X with POSIX API. The device uses a Prolific usb-serial controller, and connect to the usb port on my mac.
After I install the Prolific driver, it shows up as /dev/tty.usbserial and /dev/cu.usbserial. The vendor has published the data format. So... (1 Reply)
Discussion started by: monkeybiz
1 Replies
10. UNIX for Dummies Questions & Answers
hi. Im trying to install a switch.
And the manual says i should type a command including a SerialPortDevicePath. which is the filepath to serial port used for connection.
However.. nothing about how to find this info.
Could anyone help me where to find this path?
thx
mr.T (6 Replies)
Discussion started by: tyskertøs
6 Replies
nsd-xfer(8) nsd 3.2.12 nsd-xfer(8)
NAME
nsd-xfer - AXFR client to transfer zones from a name server
SYNOPSIS
nsd-xfer [-4] [-6] [-a address[@port]] [-p port] [-s serial] [-T tsiginfo] [-v] -z zone -f file servers
DESCRIPTION
Nsd-xfer is program to transfer zones from a name server using AXFR. NSD is a complete implementation of an authoritative DNS nameserver.
OPTIONS
-4 Only send to IPv4 addresses.
-6 Only send to IPv6 addresses.
-a address[@port]
Specify the source address (and port) to send from.
-f file
The file to store the zone in.
-p port
Specify the port to send to.
-s serial
Specify the serial of the current zone. The zone is only transferred if the master server has a zone with a greater serial number.
-T tsiginfo
Use TSIG to verify the zone transfer. The tsiginfo file must contain the TSIG key information. The file is removed upon successful
reading of the key. The format of the tsiginfo file is described in the doc/README file (section 3.3).
-v Be more verbose.
-z zone
Specify the zone to receive.
servers
List of nameservers to try.
EXAMPLES
To run this program the standard way type:
# nsd-xfer -z foobar.cz -f foobar.cz.zone 1.2.3.4
SEE ALSO
nsd(8), nsdc(8), nsd.conf(5), nsd-checkconf(8), nsd-notify(8), nsd-patch(8), zonec(8)
AUTHORS
NSD was written by NLnet Labs and RIPE NCC joint team. Please see CREDITS file in the distribution for further details.
NLnet Labs jul 19, 2012 nsd-xfer(8)