Optical drive is no longer visible after installing iTunes for Windows

4 More Discussions You Might Find Interesting

1. Hardware

Dell XPS M1330 doesn't detect optical drive

I have a Dell XPS M1330 laptop. The OS is Windows 10. I had to replace the motherboard because it was bad. After replacing the motherboard I noticed the optical (DVD/CD) drive is neither detected in BIOS and OS nor making any noise at all. Everything else seems to be working fine. The optical drive...

2. Windows & DOS: Issues & Discussions

Installing Windows 7 on a GPT drive

Hello, My hard drive was formatted with GPT. It is part of a volume group and has two logical volumes on it. Is it possible to convert the drive to MBR? If so, how would I got about doing it? I know there are programs out there that do it, but I have volume groups with LVM's so I am wondering if...

3. UNIX for Dummies Questions & Answers

trying to set up an optical drive

Trying to get my unix system to recognize an optical drive, it was delivered to us, so we assumed it worked, in the 2 years since no one ever has used it, we want to now. However, even running probe-scsi-all doesn't bring up that drive. It's a scsi address of 3, at the end of the chain, all...

4. UNIX for Advanced & Expert Users

Magneto-Optical drive for SCO Openserver 5.0.5

Hi, I tried to install Magneto-Optical (MO) drive Fujutsu to COMPAQ Proliant ML350 with SCO Openserver 5.0.5. Harddisk and MO are connected to Adaptec UW-SCSI-3 (driver ad160). During boot process system shows me that MO is connected to host adapter 1, bus 0, SCSI ID 1 and LUN 0. But when I...

LEARN ABOUT NETBSD

mlxctl

MLXCTL(8)						    BSD System Manager's Manual 						 MLXCTL(8)

NAME

     mlxctl -- Mylex DAC960 family management utility

SYNOPSIS

     mlxctl [-f dev] [-v] [-a] status [drive] [...]
     mlxctl [-f dev] [-a] detach [drive] [...]
     mlxctl [-f dev] [-a] check [drive] [...]
     mlxctl [-f dev] rebuild channel:target
     mlxctl [-f dev] cstatus
     mlxctl [-f dev] rescan
     mlxctl [-f dev] config

DESCRIPTION

     The mlxctl utility performs status monitoring and management functions for Mylex DAC960 RAID controllers and attached devices.

     The following options are available:

     -a       Apply the action to all drives attached to the controller.

     -f dev   Specify the control device to use.  The default is /dev/mlx0.

     -v       Increased verbosity.

     The following commands are available:

     cstatus  Display the controller's current status.

     status   Display the status of the specified drives.  This command returns 0 if all drives tested are online, 1 if one or more drives are
	      critical and 2 if one or more are offline.

     rescan   Re-scan the logical drive table, and attach or detach devices from the system as necessary.

     detach   Detach the specified drives.  Drives must be unmounted and unopened for this command to succeed.

     check    Initiate a consistency check and repair pass on a drive that provides redundancy (e.g., RAID1 or RAID5).	This command returns imme-
	      diately.	The status command can be used to monitor the progress of the check.

     rebuild  Rebuild onto the specified physical drive.  Note that there can be only one running rebuild operation per controller at any given
	      time.  This command returns immediately.	The cstatus command can be used to monitor the progress of the rebuild.

     config   Write the current system drive configuration to stdout.

EXAMPLES

     Display the status of drive ld3 attached to the controller mlx1:

	   mlxctl -f /dev/mlx1 -v status ld3

SEE ALSO

     ld(4), mlx(4)

HISTORY

     The mlxctl command first appeared in NetBSD 1.5.3, and was based on the mlxcontrol utility found in FreeBSD.

BUGS

     Modifying drive configuration is not yet supported.

     Some commands do not work with older firmware revisions.

     Error log extraction is not yet supported.

BSD
								  April 10, 2000							       BSD

OS X Support RSS