10 More Discussions You Might Find Interesting
1. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
2. Solaris
I am using ReflectionX on a windows PC to run an application on a Solaris box. The application uses the serial port and expects a definition like: /dev/ttyb
Is there a way to use the PC serial port through ReflectionX?
PC is running Windows-XP
Solaris Box is:
Sun Microsystems sun4u... (1 Reply)
Discussion started by: deanjennings
1 Replies
3. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
4. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
5. UNIX for Dummies Questions & Answers
A neighbour's Ubuntu 10.04 machine has five serial ports, one on the motherboard and four on a PCI card. However, only four cards are showing:
# dmesg | grep tty
console enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
... (2 Replies)
Discussion started by: dotancohen
2 Replies
6. Programming
I have a need to determine when a string has been completely sent via a serial port from a standard 'C' application. The code is as follows:
SerialPort_Send = open (pPortString, O_WRONLY | O_NOCTTY | O_NONBLOCK);
write (SerialPort_Send, pCommandString, strlen (pCommandString));
... (2 Replies)
Discussion started by: ExDes
2 Replies
7. Solaris
Hi,
I am working with solaris 9,SUN-Blade-100 and I want to communicate with the Serial port.To check whether the port is working or not.I write code and when I execute the file,then I got the output--
According to this,serial port is not found.can anyone please tell me how to configure the... (1 Reply)
Discussion started by: smartgupta
1 Replies
8. Solaris
Hi,
I am working with Sun Solaris 9 Sparc,Sun-Blade-100.In my application,I need to monitor the UPS using Serial port.
When I am using JRE 1.4 in my application,I am able to monitor it but when I am upgrading the JRE version from 1.4 to JRE1.6. I am not able to monitor the UPS.It is showing the... (1 Reply)
Discussion started by: smartgupta
1 Replies
9. SCO
Hi
I have just re-installed Compaq ML350 G2 Server with Unix SCO 5.0.5 and
informix DBMS .
on this server we have 2 serial ports , unfortunately its not working.
Can anyone help me to check the serial ports working or not OR guide me
to reconfigure it.
I have attached a device with... (1 Reply)
Discussion started by: munirh
1 Replies
10. Linux
I think my serial port(on board) is not working ......
because when I am running same code on two machines its working good....but when my system comes into picture ....it doesnt show any output comming from serial port..........
can anybody tell me how to configure my serial port.........or to... (16 Replies)
Discussion started by: arunchaudhary19
16 Replies
SCC(4) BSD Kernel Interfaces Manual SCC(4)
NAME
scc -- Zilog 8530 Serial Communications Controller interface
SYNOPSIS
scc* at ioasic? offset ?
DESCRIPTION
The scc driver provides support for the Zilog 8530 Serial Communications Controller (SCC) via the IOASIC found on DECstation 5000 models in
the /100, /20, and /240 series (supported by NetBSD/pmax).
Each SCC device has two serial ports. The DECstation 5000 model 20 provides one SCC device. Other models provide two, but one port of each
device is dedicated to mouse and keyboard input, respectively.
Input and output for each line may set to one of following baud rates: 50, 75, 110, 134.5, 150, 300, 600, 1200, 1800, 2400, 4800, 9600,
19200, 38400, or 57600.
Speeds up to 230400 are supported by the chip and the motherboard, but speeds higher than 57600 do not work reliably without an external
clock signal.
FILES
/dev/ttya
/dev/ttyb
/dev/ttyc
/dev/ttyd
The mapping from units to serial-hardware outlets is idiosyncratic. The even ports are wired serial connectors and the odd-numbered ports
are reserved for mouse and keyboard.
On machines with one port like Personal DECstations, the single device is ttya.
On the 5000/1xx and 5000/2xx, the first serial port (default serial console) is ttyc and the second port is ttya.
SEE ALSO
intro(4), ioasic(4), ttys(5), MAKEDEV(8)
HISTORY
The scc driver first appeared in 4.4BSD.
The scc driver was also used for the IOASIC SCC found in DEC Alpha model 3000 TurboCHANNEL based systems; NetBSD/alpha has since been con-
verted to use the machine-independent zstty(4).
BUGS
The IOASIC provides internal DMA channels that can be programmed to transfer up to 4096 bytes of data into, or out, of an SCC without further
software intervention. This feature of the IOASIC is not yet supported.
The mapping from device-special files (major and minor number) to chip and port is arguably backwards. ULTRIX tries to hide the hardware
mapping, but NetBSD does not. Users wanting to use ULTRIX compatible tty names /dev/tty0 and /dev/tty1 for the scc comm-port lines should
make links or device-special files which match their hardware setup.
BSD
April 24, 2003 BSD
