unix and linux operating commands

Express Lockdown

5 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Sun Storage Tek 2540 M2 controller lockdown

hello all, I have recently acquired the above server and i am having issues with the RAID controllers being put into a lockdown state. This occurs when new drives are added to the array, the controller automagically reboots and then gives status codes OE and LT. After this i am unable to...

2. Solaris

Solaris Express or OpenIndiana

Simply question which should I use. correct me if I'm wrong but Solaris Express is taking the place of Opensolaris and is officially sanctioned by Oracle and OpenIndiana is what used to be OpenSolaris. If I opt for OpenIndiana is it going to follow the official Oracle Solaris releases or are...

3. Solaris

ipfilter solaris express

Hello, | am trying to setup ipfilter on solaris express snv_91 but I don't seem to have the following file available. /etc/ipf/pfil.ap Is this an older way of configuring the interface?, I have all the packages installed. Thanks,

4. UNIX for Dummies Questions & Answers

Unix and Outlook Express

Awhile back I followed instructions in a newsletter (I don't remember which one) giving instructions on making Outlook Express very plain. Unfortunately I followed the instructions but did not make a note of the string. The last word was true. The instructions stated that if one wanted to return to...

5. Windows & DOS: Issues & Discussions

Outlook express

Where is the file where all my e-mails are stored?I know theres one file with everything in it.

LEARN ABOUT NETBSD

arcmsr

ARCMSR(4)						   BSD Kernel Interfaces Manual 						 ARCMSR(4)

NAME

     arcmsr -- Areca Technology Corporation SATA/SAS RAID controller

SYNOPSIS

     arcmsr* at pci? dev ? function ?

DESCRIPTION

     The arcmsr driver provides support for the PCI-X and PCI Express RAID controllers from Areca Technology Corporation:

	   -   ARC-1110 PCI-X 4 Port SATA RAID Controller
	   -   ARC-1110ML PCI-X 4 Port SATA RAID Controller
	   -   ARC-1120 PCI-X 8 Port SATA RAID Controller
	   -   ARC-1120ML PCI-X 8 Port SATA RAID Controller
	   -   ARC-1130 PCI-X 12 Port SATA RAID Controller
	   -   ARC-1130ML PCI-X 12 Port SATA RAID Controller
	   -   ARC-1160 PCI-X 16 Port SATA RAID Controller
	   -   ARC-1160ML PCI-X 16 Port SATA RAID Controller
	   -   ARC-1170 PCI-X 24 Port SATA RAID Controller
	   -   ARC-1200 Rev A PCI Express 2 Port SATA RAID Controller
	   -   ARC-1202 PCI Express 2 Port SATA RAID Controller
	   -   ARC-1210 PCI Express 4 Port SATA RAID Controller
	   -   ARC-1220 PCI Express 8 Port SATA RAID Controller
	   -   ARC-1230 PCI Express 12 Port SATA RAID Controller
	   -   ARC-1230ML PCI Express 12 Port SATA RAID Controller
	   -   ARC-1231ML PCI Express 12 Port SATA RAID Controller
	   -   ARC-1260 PCI Express 16 Port SATA RAID Controller
	   -   ARC-1260ML PCI Express 16 Port SATA RAID Controller
	   -   ARC-1261ML PCI Express 16 Port SATA RAID Controller
	   -   ARC-1280 PCI Express 24 Port SATA RAID Controller
	   -   ARC-1280ML PCI Express 24 Port SATA RAID Controller
	   -   ARC-1680 PCI Express 8 Port SAS RAID Controller
	   -   ARC-1680LP PCI Express 8 Port SAS RAID Controller
	   -   ARC-1680i PCI Express 8 Port SAS RAID Controller
	   -   ARC-1680x PCI Express 8 Port SAS RAID Controller
	   -   ARC-1681 PCI-X 8 Port SAS RAID Controller

     These controllers support RAID levels 0, 1, 1E, 3, 5, 6, and JBOD using either SAS or SATA II drives.

     arcmsr supports management and monitoring of the controller through the bioctl(8) and envstat(8) commands.

     Please note, however, that to use some features that require special privileges, such as creating/removing hot-spares, pass-through disks or
     RAID volumes will require to have the password disabled in the firmware; otherwise a Permission denied error will be reported by bioctl(8).

     When a RAID 1 or 1+0 volume is created, either through the bioctl(8) command or controller's firmware, the volume won't be accessible until
     the initialization is done.  A way to get access to the sd(4) device that corresponds to that volume without rebooting, is to issue the fol-
     lowing command (once the initialization is finished):

     $ scsictl scsibus0 scan any any

     The arcmsr driver will also report to the kernel log buffer any error that might appear when handling firmware commands, such as used by the
     bioctl(8) command.

EVENTS

     The arcmsr driver is able to send events to powerd(8) if a volume or any drive connected to the volume is not online.  The state-changed
     event will be sent to the /etc/powerd/scripts/sensor_drive script when such condition happens.

SEE ALSO

     intro(4), pci(4), scsi(4), sd(4), bioctl(8), envstat(8), powerd(8), scsictl(8)

HISTORY

     The arcmsr driver first appeared in NetBSD 5.0.

AUTHORS

     The arcmsr driver was originally written for OpenBSD by David Gwynne.  It was ported to NetBSD and extended by Juan Romero Pardines.

BSD
								   March 3, 2008							       BSD