Oracle's StorageTek T10000C tape drive is the first to offer the StorageTek Search Accelerator (SSA). SSA uses tape drive hardware to speed data searches, and offload that processing requirement from other data center resources.
Hi everyone,
I have a big problem and i hope u can help me. I have brand new sun server X4-2 with Solaris 10-update 10. I have to install oracle StorageTek but there is no guide or help on the internet. Can anybody help me?
CU (1 Reply)
Hi,
I recently got StoragaTek 2500 and I would like to connect it to my solaris machine, since I don't have much experience with storages, could someone point me how to do so, how can i present disks from storage on my solaris os? (everything is already connected)
thanks in advance (1 Reply)
I believe this may be a difference in GTK+-2.0 and GTK+-3.0. I followed this tutorial and ended up with this error:
# gcc -Wall -g mnemonics.c -o mnemonics `pkg-config --cflags gtk+-3.0` `pkg-config --libs gtk+-3.0`
mnemonics.c: In function ‘main':
mnemonics.c:44:61: error: ‘GDK_q' undeclared... (3 Replies)
Hello all !
I am a beginner about system and networking , and after some research on internet , i didn't find any relevant information , so i post here , if someone have an experience with this kind of material or if some documentation about how to connect my storage device on my server.
I... (2 Replies)
Hi,
I installed DirectFb on fedora 7, the machine has a Nvidia graphics card. The installation was successful and I can play the examples provided by the Direct fb website, but, I find that the accelarator is not getting recognised. when I do "fbset -i", the details shown are as below, it gives... (0 Replies)
I had been using a modem installed on a Digi accelerator port to dial in to an SCO open server r5 server. On monday it quit working and I realy don't know how it was installed and configured. I have tested the modem on a PC and it works. The port the modem is connected to is ttyB06 and I have... (1 Reply)
tz(4) Kernel Interfaces Manual tz(4)Name
tz - SCSI magnetic tape interface
Syntax
VAX NCR 5380:
adapter uba0 at nexus?
controller scsi0 at uba0 csr 0x200c0080 vector szintr
tape tz0 at scsi0 drive 0
VAX DEC SII:
adapter ibus0 at nexus?
controller sii0 at ibus? vector sii_intr
tape tz0 at sii0 drive 0
RISC DEC SII:
adapter ibus0 at nexus?
controller sii0 at ibus? vector sii_intr
tape tz0 at sii0 drive 0
RISC DEC KZQ:
adapter uba0 at nexus?
controller kzq0 at ibus? csr 0761300vector sii_intr
tape tz0 at kzq0 drive 0
RISC NCR ASC:
adapter ibus0 at nexus?
controller asc0 at ibus? vector ascintr
tape tz0 at asc0 drive 0
Description
The SCSI tape driver provides a standard tape drive interface as described in This is a driver for any Digital SCSI tape device.
For the TZK10 QIC format tape drive, the densities supported are QIC-24 (read only) block size of 512 byte blocks, QIC-120, and QIC-150
read/write block size of 512 byte blocks, and QIC-320 read/write block size of 1024 byte blocks. With QIC format style tapes all reads and
writes must be in multiple of the block size. This is a requirement of fixed block tape drives because record boundaries are not pre-
served. The QIC densities are selected using the following special device names:
QIC-24 Fixed block size.
QIC-120 Fixed block size.
QIC-150 Fixed block size.
QIC-320 Fixed block size.
With all fixed block tape devices a of a file to the tape must be padded out. An example of this is a of which has a size of approximately
3800 bytes.
dd if=/etc/gettytab of=/dev/rmt0h bs=10k conv=sync
or
dd if=/etc/gettytab of=/dev/rmt0l bs=512 conv=sync
The option of pads the output to block size.
This driver also supports n-buffered reads and writes to the raw tape interface (used with streaming tape drives). See for further
details.
Tape Support
TZ30, TZK50, TLZ04, TSZ05, TKZ08, TZK10
Diagnostics
All diagnostic messages are sent to the error logger subsystem.
FilesSee Alsomtio(4), nbuf(4), SCSI(4), MAKEDEV(8), uerf(8), tapex(8)
Guide to the Error Logger
tz(4)
