StorageTek In-Drive Reclaim Accelerator for the StorageTek T10000B Tape Drive and StorageTek Virtual
Learn how Oracle is redefining tape storage wiith the StorageTek In-Drive Reclaim Accelerator for the StorageTek T10000B tape drive and StorageTek Virtual Storage Manager.
Hi everyone,
I have a big problem and i hope u can help me. I have brand new sun server X4-2 with Solaris 10-update 10. I have to install oracle StorageTek but there is no guide or help on the internet. Can anybody help me?
CU (1 Reply)
Hi,
I recently got StoragaTek 2500 and I would like to connect it to my solaris machine, since I don't have much experience with storages, could someone point me how to do so, how can i present disks from storage on my solaris os? (everything is already connected)
thanks in advance (1 Reply)
Hi Guys and Gals,
Wionder if you could help me, got a problem with a controller on a storagetek 2540, dead when fully powered up but if you reboot, it is ok for a couple of seconds (and you can ping it). Then once the array is fully up, it goes faulty and is un-pingable.
Had anyone... (4 Replies)
Hello all !
I am a beginner about system and networking , and after some research on internet , i didn't find any relevant information , so i post here , if someone have an experience with this kind of material or if some documentation about how to connect my storage device on my server.
I... (2 Replies)
Hi peeps,
Was wondering if anyone can help me, got a couple of storagetek 2540's that I need to configure. Trouble is I think they were brought as second user as all that came with them was cables.
Does anyone know how to configure them (i.e. create raid sets and map to Luns and present... (1 Reply)
Hi,
I have recently purchase a SUN Storage Tek desktop LTO 4 HH tape drive and connected to a IBM AIX 5.1 server.
The server can detect the tape device.
Can someone please advice urgently.
Thanks (4 Replies)
We're moving our production 3510FC to development, so we need to replace the production 3510FC. The 6140 is nice, but pricey.
Here's the question: Would two 2540's (RAID 10) be 'faster' than one 3510? (RAID 10) and faster than one 6140 (RAID 10)?
One StoregeTek 6140 (16x72GB 15k rpm fc-al... (12 Replies)
AMTAPE(8) System Manager's Manual AMTAPE(8)NAME
amtape - user interface to Amanda tape changer controls
SYNOPSIS
amtape config command [ command options ]
DESCRIPTION
Amtape performs tape changer control operations. It uses the underlying tape changer script defined by the tpchanger option for a particu-
lar Amanda configuration as specified by the config argument.
Tape changers maintain a notion of the current and next slot for each configuration. These may or may not correspond to an actual physical
state of the device, but do tend to minimize searching through the tape storage slots. If the desired tape is in the current slot, it is
likely the next tape needed is in the next slot rather than at some random position in the storage slots.
See the amanda(8) man page for more details about Amanda.
COMMANDS
reset Reset the tape changer to a known state. The current slot is set to the first slot. Other device-specific side effects may occur.
Some gravity stackers need to be reset to the top position by hand. This command notifies Amanda the stacker is back in that posi-
tion.
eject If a tape is loaded in the drive, it is ejected and returned to the slot from which it was loaded.
clean If a cleaning tape is defined for the changer, it is used to clean the drive.
show Show the contents of all slots. This can be slow.
label label
Search for and load the Amanda tape with label label.
taper Perform the taper scan algorithm. Load the next tape in the configuration's tape sequence, or a fresh tape with a suitable label.
device Display the name of the current tape device on stdout.
current
Display the current slot.
update Update the changer label database, if it has one, to match the tapes now available.
slot slot
Eject any tape in the drive and put it away, then load the tape from slot slot and reset current.
slot current
Eject any tape in the drive and put it away, then load the tape from the current slot.
slot prev
Eject any tape in the drive and put it away, then load the tape from the previous slot and reset current.
slot next
Eject any tape in the drive and put it away, then load the tape from the next slot and reset current.
slot first
Eject any tape in the drive and put it away, then load the tape from the first slot and reset current.
slot last
Eject any tape in the drive and put it away, then load the tape from the last slot and reset current.
slot advance
Eject any tape in the drive and put it away. Advance current to the next tape, but do not load it.
This is useful with non-gravity stackers to unload the last tape used and set up Amanda for the next run. If you just use eject,
the current tape will be mounted again in the next run, where it will be rejected as being still in use, ejected and the next tape
requested. Using slot next followed by eject does an unnecessary mount.
Note: most changers optimize the slot commands to not eject the loaded tape if it is the one being requested.
AUTHOR
James da Silva <jds@cs.umd.edu>
University of Maryland, College Park
SEE ALSO amanda(8)AMTAPE(8)
