6 More Discussions You Might Find Interesting
1. What is on Your Mind?
Hello, I am new here and my name is Robert. I was actually looking for a forums website where I can go with questions regarding Linux and embedded Linux applications. I am fairly new (6 months) to the world of Linux and embedded Linux applications and the the learning curve is steep. When I am not... (13 Replies)
Discussion started by: Circuits
13 Replies
2. IP Networking
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies
3. IP Networking
Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? "
A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Discussion started by: Ayaerlee
0 Replies
4. IP Networking
Hi,
I am trying to establish vpn between my linux server and cisco asa at client side.
I installed openswan on my cent os.
Linux Server
eth0 - 182.2.29.10
Gateway - 182.2.29.1
eth1 - 192.9.200.75
I have simple IPtables Like
WAN="eth0"
LAN="eth1" (0 Replies)
Discussion started by: ashokvpp
0 Replies
5. AIX
Using nimadm:
nimadm -j nimadmvg -c sap024 -s spot_6100 -l lpp_6100 -d "hdisk1" -Y
Initializing the NIM master.
Initializing NIM client sap024.
0505-205 nimadm: The level of bos.alt_disk_install.rte installed in SPOT
spot_6100 (6.1.3.4) does not match the NIM master's level (7.1.1.2).... (2 Replies)
Discussion started by: sciacca75
2 Replies
6. IP Networking
Setup a site to site VPN between two cisco routers.
One of the site locations is unable to access ports such as https://example.com:9001
How do I let them go into port 9001?
They can ssh, ftp, telnet and everything else.
Is this a VPN issue or ACL access issue?
I put
permit ip host... (0 Replies)
Discussion started by: photon
0 Replies
DATE(1) General Commands Manual DATE(1)
NAME
date - print or set the date and time
SYNOPSIS
date [-qsu] [[MMDDYY]hhmm[ss]] [+format]
OPTIONS
-q Read the date from stdin
-s Set the time (implicit for -q or a date string)
-u Print the date as GMT
-t Use this number of seconds instead of current time
EXAMPLES
date # Print the date and time
date 0221921610 # Set date to Feb 21, 1992 at 4:10 p.m.
DESCRIPTION
With the -q flag or a numeric argument, date sets the GMT time and date. MMDDYY refers to the month, day, and year; hhmmss refers to the
hour, minute and second. Each of the six fields must be exactly two digits, no more and no less. date always display the date and time,
with the default format for the system. The -u flag request GMT time instead of local time. A format may be specified with a + followed
by a printf-like string with the following options:
%% % character
%A Name of the day
%B Name of the month
%D mm/dd/yy
%H Decimal hour on 2 digits
%I Decimal hour modulo 12 on 2 digits
%M Decimal minute on 2 digits
%S Decimal seconds on 2 digits
%T HH:MM:SS
%U Decimal week number, Sunday being first day of week
%W Decimal week number, Monday being first day of week
%X Same as %T
%Y Decimal year on 4 digits
%Z Time Zone (if any)
%a Abbreviated name of the day
%b Abbreviated name of the month
%c Appropriate date & time (default format)
%d Decimal day of the month on 2 digits
%e Same as %d, but a space replaces leading 0
%h Same as %b
%j Decimal dey of the year on 3 digits
%m Decimal month on 2 digits
%n Newline character
%p AM or PM
%r 12-hour clock time with AM/PM
%s Number of seconds since the epoch
%t Tab character
%w Decimal day of the week (0=Sunday)
%x Same as %D
%y Decimal year on 2 digits
SEE ALSO
time(2), ctime(3), readclock(8).
DATE(1)