FMVJ18x_CS(4) Kernel Interfaces Manual FMVJ18x_CS(4)y.NAME
fmvj18x_cs - Fujitsu FMV-J18x series device driver
SYNOPSIS
insmod fmvj18x_cs.o [pc_debug=n] [fmvj18x_debug=n] [irq_list=i,j,...]
DESCRIPTION
fmvj18x_cs is the low-level Card Services driver for the Fujitsu FMV-J18x series PCMCIA ethernet adapter. When this driver is attached to
a card, it allocates the next available ethernet device (eth0..eth#). This device name will be reported in the kernel log file, and passed
on to cardmgr(8).
PARAMETERS
pc_debug=n
Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero
value enables debugging.
fmvj18x_debug=n
Selects the network debugging level. The current default is 3; values of up to six increase reporting verbosity.
irq_list=i,j,...
Specifies the set of interrupts that may be allocated by this driver.
AUTHOR
Shingo Fujimoto - Fujitsu Laboratories Ltd. <Shingo@flab.fujitsu.co.jp>
THANKS
Yutaka TAMIYA - Fujitsu Laboratories Ltd.
Hideaki Yoda - Fujitsu Limited.
SEE ALSO cardmgr(8), pcmcia(5).
1999/02/08 08:02:01 FMVJ18x_CS(4)
Check Out this Related Man Page
SERIAL_CS(4) Kernel Interfaces Manual SERIAL_CS(4)NAME
serial_cs - PCMCIA serial port driver
SYNOPSIS
insmod serial_cs.o [pc_debug=n] [irq_list=i,j,...] [do_sound=n]
DESCRIPTION
Serial_cs is the Card Services driver for all PCMCIA serial devices, including modem cards. When serial_cs is bound to a serial or modem
card, it will generally attempt to allocate the first unused serial device for use by the card. The device chosen will be recorded in the
kernel log file, and will also be reported to cardmgr(8). The major and minor numbers and device name reported by serial_cs will match the
corresponding "dialout" device (/dev/cua#). The new device can be accessed using this device file or the corresponding /dev/ttyS# device.
The default serial card setup script will link the dialout device to /dev/modem.
PARAMETERS
pc_debug=n
Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero
value enables debugging.
irq_list=i,j,...
Specifies the set of interrupts that may be allocated by this driver.
do_sound=n
A flag specifying if speaker output should be enabled. The default is 1 (true). Set to 0 to disable speaker output.
AUTHOR
David Hinds - dahinds@users.sourceforge.net
SEE ALSO cardmgr(8), pcmcia(5).
pcmcia-cs 2000/06/12 21:24:48 SERIAL_CS(4)
hello,
I am getting an insmod error on my pcmcia lan card. upon boot, it gives me the insmod error and says that it might be an irq setting or an io setting.
because of this error, the eth0 interface is obviously not working.
how do i check for irq conflicts or troubleshoot this.
thank you. (1 Reply)
Im newest in unix,
Please, give me solution for installing lan adapter if driver not found in the list of ethernet drivers
ihave unix driver in a dos diskete
please give me the other solution
and tell me where the domain of unix class online, so ican read from it.
Thank's very much (3 Replies)
hi everybody
i installed FreeBSD 5.x on a box with a video card Diamond SpeedStar A90 and a Fujitsu Siemens Monitor B772-1
when i do "startx" it gives me something like this:
fatal error: no devices detected
no screen detected
i'm lost...i don't know what to... (3 Replies)
Hi Everyone,
I am relatively new to Linux. After about three months of trying to compile a driver for a ESDCAN card, I finally found a version and kernel that worked. I am running Slackware V12.0 with kernel version 2.6.24.5-smp. When I use insmod to insert the driver file (esdcan-pci331.ko),... (1 Reply)
I have a new SAN (Fujitsu Eternus 2000) and am trying to setup a veritas cluster on it, however veritas does not see all of the vluns I have exposed to the box. The OS does see them though. I have seen a lot of post about this, but it seems they are about people having just the opposite problem... (0 Replies)
Hi all,
I have an access Fujitsu primepower 650 that I can play with, the problem is I think there is a hardware problem I need to resolve before I can use it.
Tried reading the User manual about the error code and googling it, but no luck, anyone knows here how to troubleshoot one?
Error... (2 Replies)
Hi,
I have file
#cat drivers.txt
fcs0
fcs1
vscsi1
vscsi2
In this i need to check the availabality of "fcs" or "vscsi" alone not vscsi0,fcs1
I tried with "if condition" but it is not working.
cat drivers.txt| while read ADAP
do
echo "Checking for $ADAP"
if ;then
echo "FC... (9 Replies)
Hello, I need migrate our applications from M-series to T-series. I would like compare two different SPARC processors - SPARCVII+ from Fujitsu and T5 from Oracle. I found only next benchmarks:
M8000:
... (9 Replies)
Hello.
I have a server RS/6000 with AIX 4.2. The server have a network card with 10/100mbps speed, but for some reason, the ethernet only runs at 10Mbps, it doesn,t matter if I put the net cable on a 100Mbps switch, it keeps running at 10Mbps speed....
I know how to view/change ethernet speed... (1 Reply)