fmvj18x_cs(4) [redhat man page]

FMVJ18x_CS(4)						     Kernel Interfaces Manual						     FMVJ18x_CS(4)

y.

NAME

       fmvj18x_cs - Fujitsu FMV-J18x series device driver

SYNOPSIS

       insmod fmvj18x_cs.o [pc_debug=n] [fmvj18x_debug=n] [irq_list=i,j,...]

DESCRIPTION

       fmvj18x_cs  is the low-level Card Services driver for the Fujitsu FMV-J18x series PCMCIA ethernet adapter.  When this driver is attached to
       a card, it allocates the next available ethernet device (eth0..eth#).  This device name will be reported in the kernel log file, and passed
       on to cardmgr(8).

PARAMETERS

       pc_debug=n
	      Selects  the PCMCIA debugging level.  This parameter is only available if the module is compiled with debugging enabled.	A non-zero
	      value enables debugging.

       fmvj18x_debug=n
	      Selects the network debugging level.  The current default is 3; values of up to six increase reporting verbosity.

       irq_list=i,j,...
	      Specifies the set of interrupts that may be allocated by this driver.

AUTHOR

       Shingo Fujimoto - Fujitsu Laboratories Ltd.  <Shingo@flab.fujitsu.co.jp>

THANKS

       Yutaka TAMIYA - Fujitsu Laboratories Ltd.

       Hideaki Yoda - Fujitsu Limited.

SEE ALSO

       cardmgr(8), pcmcia(5).

								1999/02/08 08:02:01						     FMVJ18x_CS(4)

3C589_CS(4)						     Kernel Interfaces Manual						       3C589_CS(4)

NAME

       3c589_cs - 3Com 3c589 Etherlink III device driver

SYNOPSIS

       insmod 3c589_cs.o [pc_debug=n] [if_port=n] [irq_list=i,j,...]

DESCRIPTION

       3c589_cs  is  the  low-level  Card  Services driver for the 3Com 3c589 PCMCIA ethernet adapter and 3Com 3c562/3c563 combo cards.  When this
       driver is attached to a card, it allocates the next available ethernet device (eth0..eth#).  This device name will be reported in the  ker-
       nel log file, and passed on to cardmgr(8).

       With  the default transceiver setting, the driver will attempt to continuously autodetect the transceiver type (10base2 or 10baseT).  There
       should normally only be a one or two second lag before the correct transceiver is selected.  On particularly noisy or busy networks, it	is
       possible  for the detection logic to incorrectly toggle the transceiver type.  If this becomes a problem, it may be necessary to explicitly
       select the interface type when the module is loaded or with the ifport command.

PARAMETERS

       pc_debug=n
	      Selects the PCMCIA debugging level.  This parameter is only available if the module is compiled with debugging enabled.  A  non-zero
	      value enables debugging.

       if_port=n
	      Selects  the  transceiver type.  0 is autodetect (10baseT or 10base2), 1 is 10baseT (twisted pair), 2 is 10base2 (BNC, or thin net).
	      and 3 is AUI (thick ethernet).  The default is 0 (autodetect).

       irq_list=i,j,...
	      Specifies the set of interrupts that may be allocated by this driver.

DIAGNOSTICS

       eth#: interrupt(s) dropped!
	      Indicates that the driver did not receive an interrupt notification for some reason.  The driver will poll the card (with a signifi-
	      cant  performance penalty) if the problem persists.  The most likely cause is an interrupt conflict and/or host bridge configuration
	      problem.

AUTHOR

       David Hinds - dahinds@users.sourceforge.net

SEE ALSO

       cardmgr(8), pcmcia(5), ifport(8).

pcmcia-cs							2000/06/12 21:24:48						       3C589_CS(4)