xirc2ps_cs(4) [redhat man page]

XIRC2PS_CS(4)						     Kernel Interfaces Manual						     XIRC2PS_CS(4)

NAME

       xirc2ps_cs - Xircom CE2ps (and newer) device driver

SYNOPSIS

       insmod xirc2ps_cs.o [pc_debug=n] [full_duplex=n] [irq_list=i,j,...]  [if_port=n] [lockup_hack=n]

DESCRIPTION

       xirc2ps_cs  is  the low-level Card Services driver for the Xircom 16-bit PCMCIA ethernet adapters.  When this driver is attached to a card,
       it allocates the next available ethernet device.

PARAMETERS

       pc_debug=n
	      Selects the PCMCIA debugging level.  This parameter is only available if the module is compiled with debugging enabled.  A  non-zero
	      value enables debugging.

       if_port=n
	      Selects  the transceiver type, for some CE3B-100 cards that lack the ability to autonegotiate.  For such cards, a value of 1 selects
	      10baseT, and 4 selects 100baseT.

       full_duplex=n
	      Selects full duplex mode.  The default is 0 (half duplex).

       irq_list=i,j,...
	      Specifies the set of interrupts that may be allocated by this driver.

       lockup_hack=n
	      Enables a hack to avoid lockups on some cards.	Use this only if you really have lockup problems with your card.

SEE ALSO

       cardmgr(8), pcmcia(5).

BUGS

       Please report to <xircom-bugs@isil.d.shuttle.de>

AUTHOR

       Werner Koch <werner.koch@guug.de>

							     1.5  1998/09/15 12:40:59						     XIRC2PS_CS(4)

3C589_CS(4)						     Kernel Interfaces Manual						       3C589_CS(4)

NAME

       3c589_cs - 3Com 3c589 Etherlink III device driver

SYNOPSIS

       insmod 3c589_cs.o [pc_debug=n] [if_port=n] [irq_list=i,j,...]

DESCRIPTION

       3c589_cs  is  the  low-level  Card  Services driver for the 3Com 3c589 PCMCIA ethernet adapter and 3Com 3c562/3c563 combo cards.  When this
       driver is attached to a card, it allocates the next available ethernet device (eth0..eth#).  This device name will be reported in the  ker-
       nel log file, and passed on to cardmgr(8).

       With  the default transceiver setting, the driver will attempt to continuously autodetect the transceiver type (10base2 or 10baseT).  There
       should normally only be a one or two second lag before the correct transceiver is selected.  On particularly noisy or busy networks, it	is
       possible  for the detection logic to incorrectly toggle the transceiver type.  If this becomes a problem, it may be necessary to explicitly
       select the interface type when the module is loaded or with the ifport command.

PARAMETERS

       pc_debug=n
	      Selects the PCMCIA debugging level.  This parameter is only available if the module is compiled with debugging enabled.  A  non-zero
	      value enables debugging.

       if_port=n
	      Selects  the  transceiver type.  0 is autodetect (10baseT or 10base2), 1 is 10baseT (twisted pair), 2 is 10base2 (BNC, or thin net).
	      and 3 is AUI (thick ethernet).  The default is 0 (autodetect).

       irq_list=i,j,...
	      Specifies the set of interrupts that may be allocated by this driver.

DIAGNOSTICS

       eth#: interrupt(s) dropped!
	      Indicates that the driver did not receive an interrupt notification for some reason.  The driver will poll the card (with a signifi-
	      cant  performance penalty) if the problem persists.  The most likely cause is an interrupt conflict and/or host bridge configuration
	      problem.

AUTHOR

       David Hinds - dahinds@users.sourceforge.net

SEE ALSO

       cardmgr(8), pcmcia(5), ifport(8).

pcmcia-cs							2000/06/12 21:24:48						       3C589_CS(4)