ndmp(4) [opensolaris man page]

ndmp(4) 							   File Formats 							   ndmp(4)

NAME

       ndmp - configuration properties for Solaris Network Data Management Protocol (NDMP) server

DESCRIPTION

       The behavior of the Solaris NDMP server is specified by property values that are stored in the Service Management Facility, smf(5).

       An authorized user can use the ndmpadm(1M) command to set global values for these properties in SMF.

       You can set the following properties by using the ndmpadm set command:

       backup-quarantine       Backup the files marked as quarantined by AV. Acceptable values are yes or no. The default is no.

       dar-support	       Set the Direct Access Recovery mode. Acceptable values are yes or no. The default is no.

       debug-level	       Set the debug level. The debug-level can be set to either 0 (off) or 1 (on). The default is 0.

       debug-path	       The path to which to save the debug log. The default is /var/ndmp.

       dump-pathnode	       Enable  or  disable  backing  up the directories containing modified files or directories in dump(1) backup format.
			       Acceptable values are yes or no. The default is no.

       ignore-ctime	       Determines whether the change timestamp (ctime) of files and directories is used to determine whether a file should
			       be  backed  up  in level backup. If this parameter is set to yes, only the modification time (mtime) of the file or
			       directory determines whether it should be backed up. Acceptable values are yes or no. The default value is no.

       overwrite-quarantine    Restore quarantined files on top of current files if they already exist. Acceptable  values  are  yes  or  no.  The
			       default value is no.

       restore-quarantine      Restore the files that had been marked as quarantined by AV and are backed up. Acceptable values are yes or no. The
			       default value is no.

       tar-pathnode	       Enable or disable backing up the directories containing modified files or  directories  in  tar(1)  backup  format.
			       Acceptable values are yes or no. The default value is no.

       token-maxseq	       Set  the  maximum sequence number for subsequent token-based incremental backup in NDMP-V4. The default value is 9.
			       There are two limits for this value: soft-limit, which is 59, and hard-limit, equal to 64. If  the  token  sequence
			       number,	passed	by the DMA, is between the soft and hard limits, a warning message is issued to the DMA. The token
			       sequence number can never exceed the hard-limit value.

       version		       Set the maximum active NDMP protocol version. Valid values are currently 2, 3, and 4. The default is 4.

       The following property can only be set when using the ndmpadm enable or ndmpadm disable command:

       auth-type    Sets the password encryption type for the authentication of local users. Valid values are cram-md5 or cleartext.

ATTRIBUTES

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWndmpu, SUNWndmpr	   |
       +-----------------------------+-----------------------------+
       |Interface Stability	     |Committed 		   |
       +-----------------------------+-----------------------------+

SEE ALSO

       dump(1), tar(1), ndmpadm(1M), ndmpd(1M), attributes(5), smf(5)

SunOS 5.11							    3 Mar 2009								   ndmp(4)

Check Out this Related Man Page

plimit(1)                                                          User Commands                                                         plimit(1)

NAME

       plimit - get or set the resource limits of running processes

SYNOPSIS

       plimit [-km] pid...

       plimit {-cdfnstv} soft,hard... pid...

DESCRIPTION

       If  one  or more of the cdfnstv options is specified, plimit sets the soft (current) limit and/or the hard (maximum) limit of the indicated
       resource(s) in the processes identified by the process-ID list, pid. Otherwise plimit reports the resource limits of the processes  identi-
       fied by the process-ID list, pid.

       Only  the  owner  of a process or the super-user is permitted either to get or to set the resource limits of a process. Only the super-user
       can increase the hard limit.

OPTIONS

       The following options are supported:

       -k       On output, show file sizes in kilobytes (1024 bytes) rather than in 512-byte blocks.

       -m       On output, show file and memory sizes in megabytes (1024*1024 bytes).

       The remainder of the options are used to change specified resource limits. They each accept an argument of the form:

              soft,hard

       where soft specifies the soft (current) limit and hard specifies the hard (maximum) limit. If the hard limit is not  specified,  the  comma
       may  be  omitted. If the soft limit is an empty string, only the hard limit is set. Each limit is either the literal string unlimited, or a
       number, with an optional scaling factor, as follows:

       nk       n kilobytes

       nm       n megabytes (minutes for CPU time)

       nh       n hours (for CPU time only)

       mm:ss    minutes and seconds (for CPU time only)

       The soft limit cannot exceed the hard limit.

       -c soft,hard    Set core file size limits (default unit is 512-byte blocks).

       -d soft,hard    Set data segment (heap) size limits (default unit is kilobytes).

       -f soft,hard    Set file size limits (default unit is 512-byte blocks).

       -n soft,hard    Set file descriptor limits (no default unit).

       -s soft,hard    Set stack segment size limits (default unit is kilobytes).

       -t soft,hard    Set CPU time limits (default unit is seconds).

       -v soft,hard    Set virtual memory size limits (default unit is kilobytes).

OPERANDS

       The following operands are supported.

       pid      Process ID list.

EXIT STATUS

       plimit returns the exit value zero on success, non-zero on failure (such as no such process, permission denied, or invalid option).

FILES

       /proc/pid/*     process information and control files

ATTRIBUTES

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE         |      ATTRIBUTE VALUE        |
       +-----------------------------+-----------------------------+
       |Availability                 |SUNWesu                      |
       +-----------------------------+-----------------------------+

SEE ALSO

       ulimit(1), proc(1), getrlimit(2), setrlimit(2), proc(4), attributes(5),

SunOS 5.10                                                          8 Jun 1998                                                           plimit(1)

Linux and UNIX Man Pages

ndmp(4) [opensolaris man page]

Check Out this Related Man Page