UKBD(4) BSD Kernel Interfaces Manual UKBD(4)NAME
ukbd -- USB keyboard support
SYNOPSIS
ukbd* at uhidev? reportid ?
wskbd* at ukbd? console ?
DESCRIPTION
The ukbd driver provides support for USB keyboards (i.e., HID devices with reports in usage page 7). Access to the keyboard is through the
wscons(4) driver.
SEE ALSO uhidev(4), usb(4), wskbd(4)HISTORY
The ukbd driver appeared in NetBSD 1.4.
BUGS
The ukbd driver is brought into action rather late in the boot process, so if it is used as the console driver then ddb(4) is not usable
until late in the boot.
BSD July 12, 1998 BSD
Check Out this Related Man Page
UKBD(4) BSD Kernel Interfaces Manual UKBD(4)NAME
ukbd -- USB keyboard driver
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device ukbd
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
ukbd_load="YES"
DESCRIPTION
The ukbd driver provides support for keyboards that attach to the USB port. usb(4) and one of uhci(4) or ohci(4) must be configured in the
kernel as well.
CONFIGURATION
By default, the keyboard subsystem does not create the appropriate devices yet. Make sure you reconfigure your kernel with the following
option in the kernel config file:
options KBD_INSTALL_CDEV
If both an AT keyboard USB keyboards are used at the same time, the AT keyboard will appear as kbd0 in /dev. The USB keyboards will be kbd1,
kbd2, etc. You can see some information about the keyboard with the following command:
kbdcontrol -i < /dev/kbd1
or load a keymap with
kbdcontrol -l keymaps/pt.iso < /dev/kbd1
See kbdcontrol(1) for more possible options.
You can swap console keyboards by using the command
kbdcontrol -k /dev/kbd1
From this point on, the first USB keyboard will be the keyboard to be used by the console.
If you want to use a USB keyboard as your default and not use an AT keyboard at all, you will have to remove the device atkbd line from the
kernel configuration file. Because of the device initialization order, the USB keyboard will be detected after the console driver initial-
izes itself and you have to explicitly tell the console driver to use the existence of the USB keyboard. This can be done in one of the fol-
lowing two ways.
Run the following command as a part of system initialization:
kbdcontrol -k /dev/kbd0 < /dev/ttyv0 > /dev/null
(Note that as the USB keyboard is the only keyboard, it is accessed as /dev/kbd0) or otherwise tell the console driver to periodically look
for a keyboard by setting a flag in the kernel configuration file:
device sc0 at isa? flags 0x100
With the above flag, the console driver will try to detect any keyboard in the system if it did not detect one while it was initialized at
boot time.
DRIVER CONFIGURATION
options KBD_INSTALL_CDEV
Make the keyboards available through a character device in /dev.
options UKBD_DFLT_KEYMAP
makeoptions UKBD_DFLT_KEYMAP=fr.iso
The above lines will put the French ISO keymap in the ukbd driver. You can specify any keymap in /usr/share/syscons/keymaps with this
option.
options KBD_DISABLE_KEYMAP_LOADING
Do not allow the user to change the keymap. Note that these options also affect the AT keyboard driver, atkbd(4).
FILES
/dev/kbd* blocking device nodes
EXAMPLES
device ukbd
Add the ukbd driver to the kernel.
SEE ALSO kbdcontrol(1), ohci(4), syscons(4), uhci(4), usb(4), config(8)AUTHORS
The ukbd driver was written by Lennart Augustsson <augustss@cs.chalmers.se> for NetBSD and was substantially rewritten for FreeBSD by
Kazutaka YOKOTA <yokota@zodiac.mech.utsunomiya-u.ac.jp>.
This manual page was written by Nick Hibma <n_hibma@FreeBSD.org> with a large amount of input from Kazutaka YOKOTA
<yokota@zodiac.mech.utsunomiya-u.ac.jp>.
BSD November 22, 2006 BSD