STPCIDE(4) BSD Kernel Interfaces Manual STPCIDE(4)NAME
stpcide -- STMicroelectronics STPC IDE disk controllers driver
SYNOPSIS
stpcide* at pci? dev ? function ? flags 0x0000
DESCRIPTION
The stpcide driver supports the STMicroelectronics STPC x86 SoC internal IDE controllers, and provides the interface with the hardware for
the ata(4) driver. The driver features DMA mode 2 and PIO mode 4 transfer speeds.
The 0x0002 flag forces the stpcide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debug-
ging aid, or to work around problems where the IDE controller is wired up to the system incorrectly.
SEE ALSO ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)BUGS
The timings used for the DMA and PIO modes are for STPC Atlas and its siblings with their PCI clock configured at 33 MHz. Other speeds
including the STPC Vega Ultra-IDE controller will need adjustments.
BSD October 31, 2003 BSD
Check Out this Related Man Page
CMDIDE(4) BSD Kernel Interfaces Manual CMDIDE(4)NAME
cmdide -- CMD Technology and Silicon Image IDE disk controllers driver
SYNOPSIS
cmdide* at pci? dev ? function ? flags 0x0000
options PCIIDE_CMD064x_DISABLE
options PCIIDE_CMD0646U_ENABLEUDMA
DESCRIPTION
The cmdide driver supports the CMD Technology PCI0640, PCI0643, PCI0646, PCI0648, PCI0649, and Silicon Image 0680 IDE controllers, and pro-
vides the interface with the hardware for the ata(4) driver.
The 0x0002 flag forces the cmdide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debugging
aid, or to work around problems where the IDE controller is wired up to the system incorrectly.
SEE ALSO ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)BUGS
There's no way to reliably know if a PCI064x controller is enabled or not. If the driver finds a PCI064x, it will assume it is enabled
unless the PCIIDE_CMD064x_DISABLE option is specified in the kernel config file. This will be a problem only if the controller has been dis-
abled in the BIOS and another controller has been installed and uses the ISA legacy I/O ports and interrupts.
The PCI0646U controller is known to be buggy with Ultra-DMA transfers, so Ultra-DMA is disabled by default for this controller. To enable
Ultra-DMA, use the PCIIDE_CMD0646U_ENABLEUDMA option. Ultra-DMA can eventually be disabled on a per-drive basis with config flags, see
wd(4).
The timings used for the PIO and DMA modes for controllers listed above are for a PCI bus running at 30 or 33 MHz. This driver may not work
properly on overclocked systems.
BSD December 13, 2003 BSD
hi,
I am unable to install unix open server 5.0.2 on desktop P-III,750 MHz,20GB HDD (IDE) 1.44 MB FDD, ATAPI IDE 48X cd rom. I prepared 5 boot floppies i.e. boot(N00), AHSBTLD(01), IPXSPX(01),NUC(01), NUC(02). The system was booted with boot(N00) floppy. After booting it asked to identify... (3 Replies)
Hi folks
I'm looking for a easy-to-use C/C++ IDE to develop application for X-windows on FreeBSD (window manager is OpenBox, and I don't have KDE/Gnome installed)!
Is there a good programming IDE for this?? (1 Reply)
My Ultra 5 (Solaris 10) is now unbootable, with the OBP failing with error "trap 3e" When it tries to boot from disk.
Disk is a Maxtor 80GB IDE, and was working previously.
I've booted to cdrom and run "Format" from Single user, but when I try to read the disk, it just core dumps.
I have... (2 Replies)
Hello all
Im looking for IDE to edit / compile / debug similar to VC++ on windows
I need it for verity of UNIX platforms, what do you think is the best tool to use
And that its learning carve is easy ( as much as possible) .
Thanks (9 Replies)
Ok firstly i must say that i have just switched to Ubuntu and Linux, so im a real newbie!!!
Next is that im trying to learn C, so i got an IDE called Geany.
Im following this tutorial on c and all is fine on the first example, i created the code, compiled, linked and get my EXE.
Now here comes... (1 Reply)
recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Hi there all, *again* :P
well I have a problem.
I added a new HD in my system specially for my VMachines.
in the bios I see the HD come up (its an old IDE HD that is inserted as slave)
So I would think that I should see him as /dev/hdb
but I dont see him at all in fdisk or what so ever.
I... (3 Replies)
Hello
I own a SPARC Ultra 10 workstation (standalone) and when issuing the fsck command I get the following output on fs C0t0d0s7:
Phase 1 (checks blocks and sizes):
dada warning: /pci@lf;0/pci@1, 1/ide@3/dad@0,0(dad1): ATA Transport failed:reason, `incomplete'>
Uncorrectable data... (2 Replies)
I have Sun Ultra 5/10 UltraSPARC-IIi 440 Mhz ) OpenBoot 3.19 with 1024 MB and IDE disk
I have the following error shown in the attached photos and video kindly advise (5 Replies)
Hello
I'm trying to virtualize an instance of Sco Unix 5.0.5 in VirtualBox (called VM-A) , but sco I have problems set to launch with the new raid controller .
The physical machine has a raid controller adaptec (alad driver) but VirtualBox uses buslogic (blc driver)
What ... (3 Replies)
Hi,
I need an IDE for my C application based on AIX 5.3
is there any IDE that I could use directly in AIX or I have to use X window server to visualise it on windows?
Thanks in advance
Hasnaa (3 Replies)
Ubuntu, Bash 4.3.48
Hi,
I have this input file with many columns separated with ":"
ARC=121:ERF=12244:IDE=2334:ADA=34 ....
ERF=124:ARC=123:IDE=2344:ADA=54 ....
ERF=16254:IDE=2434:ADA=78:ARC=134 ....
and I want this:
ARC=121:IDE=2334
ARC=123:IDE=2344
ARC=134:IDE=2434
I need to... (5 Replies)