Linux and UNIX Man Pages

Linux & Unix Commands - Search Man Pages

amhphy(4) [netbsd man page]

AMHPHY(4)						   BSD Kernel Interfaces Manual 						 AMHPHY(4)

NAME
amhphy -- Driver for the AMD 79c901 10BASE-T PHY SYNOPSIS
amhphy* at mii? phy ? DESCRIPTION
The amhphy driver supports the 10BASE-T portion of the AMD 79c901 HomePNA/10BASE-T PHY. SEE ALSO
ifmedia(4), intro(4), mii(4), ifconfig(8) BSD
August 24, 2001 BSD

Check Out this Related Man Page

TL(4)							   BSD Kernel Interfaces Manual 						     TL(4)

NAME
tl -- Ethernet driver for Texas Instruments ThunderLAN based board SYNOPSIS
tl* at pci? dev ? function ? Configuration of PHYs is necessary. See mii(4). DESCRIPTION
The tl device driver supports network adapters based on the Texas Instruments ThunderLAN chip. HARDWARE
Supported cards include: Compaq Netelligent in baseboard and PCI variants (10BASE-T-only variant untested). Compaq NetFlex 3/P in baseboard variant only (the PCI variant doesn't use the same chip!). It Baseboard Compaq Deskpro 4000 5233MMX Ethernet (This has been tested on the Deskpro 4000M only). TI TravelMate 5000 series laptop docking station's Ethernet board. MEDIA SELECTION
The different models of the supported boards come with some subset of RJ-45, BNC and AUI connectors. Media selection is done using ifconfig(8) using the standard ifmedia(4) mechanism. Refer to those manual pages for more information. The tl driver doesn't have full automatic media selection. By default it will do an Nway (IEEE 802.3u) negotiation on the 10BASE-T port for the speed and duplex mode with the link partner. If the AUI or BNC port is used, an explicit media type must be specified to ifconfig(8). SEE ALSO
ifmedia(4), mii(4), netintro(4), pci(4), ifconfig(8) BUGS
The board marked as untested will always claim having an AUI connector, where it may be a BNC one. BSD
May 16, 2009 BSD
Man Page

13 More Discussions You Might Find Interesting

1. Tips and Tutorials

Unix File Permissions

Introduction I have seen some misinformation regarding Unix file permissions. I will try to set the record straight. Take a look at this example of some output from ls: $ ls -ld /usr/bin /usr/bin/cat drwxrwxr-x 3 root bin 8704 Sep 23 2004 /usr/bin -r-xr-xr-x 1 bin bin ... (6 Replies)
Discussion started by: Perderabo
6 Replies

2. Shell Programming and Scripting

sorting left-justified numeric values

I have a file which looks roughly like this: 996 mmmmmmm 996 xxxxxxxxxxxxx 99600 ssssssssss 9964 fffffffffffff and would like to sort it numerically on the first field. I tried: sort -nr --key=1 .... The output I get is: 99600 ssssssssss 9964 ... (3 Replies)
Discussion started by: rovf
3 Replies

3. Programming

Memory Leaks

Suppose I have a main() function with only one malloc statement allocating say some 1 gb memory. Also say my system has 1 gb of ram. main() { malloc(1gb) return(0) } The program above exits without freeing the memory. In this case will the 1 gb of heap memory be returned... (9 Replies)
Discussion started by: rupeshkp728
9 Replies

4. Solaris

How to install PGX32 on Sparc 10 Ultra?

I'm trying to install a PGX32 video card on my Sparc 10 Ultra running Solaris 10. I've got the Oracle installation guide for it and I got as far as: "4. Insert the CD-ROM labeled “GFX OpenWindows for Solaris 2” into the drive." I don't have a CD-ROM by that name and a web search for that... (21 Replies)
Discussion started by: Michele31416
21 Replies

5. Shell Programming and Scripting

Better to Use Return Code or wc -l Output?

Hey All, Quick question... I'm writing a short script to check if a continuous port is running on a server. I'm using "ps -ef | grep -v grep | grep processName" and I was wondering if it was better/more reliable to just check the return code from the command or if its better to pipe to... (12 Replies)
Discussion started by: mrm5102
12 Replies

6. Shell Programming and Scripting

Vm versus physical linux server

Does anyone have a script that can be run to tell you if you are on either a VM Linux or a physical Linux server? (15 Replies)
Discussion started by: bigbenn
15 Replies

7. BSD

NetBSD 6.1.2: apm and admd not found

I installed NetBSD 6.1.2 amd64 and can't find the apm utility. Is it not in the base system? Is it necessary to recompile the default amd64 kernel to use apm? Or is there a new method for power management and suspend/resume? (2 Replies)
Discussion started by: bsdx
2 Replies

8. Shell Programming and Scripting

RFC - Korn shell prompt

Hi, I am learning shell scripting for the first time. I use AT&T Korn Shell, Version AJM 93u+ 2012-08-01, compiled from source on NetBSD. So far I have managed to set up what I think is a useful and pleasing shell prompt, which can be seen in the image attached to this post. The prompt is... (2 Replies)
Discussion started by: gezley
2 Replies

9. Shell Programming and Scripting

Make bold chars in UNIX

Hi all, I want to make the string as bold in unix. is there any way to acheive this? thanks in advance. (16 Replies)
Discussion started by: SekhaReddy
16 Replies

10. Shell Programming and Scripting

Adding a List of Times

Hey gang, I have a list of times I need to sum up. This list can vary from a few to a few thousand entries. Now I had found a closed reference to adding time titled "add up time with xx:yy format in bash how?" In it, the example works great for that formatted list of times... This is the reply code... (5 Replies)
Discussion started by: Brusimm
5 Replies

11. UNIX for Beginners Questions & Answers

BSD Unix Toolbox: 1000+ Commands for FreeBSD, OpenBSD, and NetBSD

Usually when I on the evening go to bed I take some interesting book with me. I read it for a while to get me down to sleep. Probably most people seek information from the Nett by googleing but I am so oldfashioned I prefer a real book ;) But what a book. The one I found and ordered is BSD Unix®... (0 Replies)
Discussion started by: fossiili
0 Replies

12. UNIX for Beginners Questions & Answers

Grandpa returning to UNIX

On the late 1960s I got short hands on experience with a russian "small" computer. It vas a copy of DEC's VAX ... and running some version of BSD-Unix. After that I worked in a university following the development of computing. After retire I started collecting old pc's and installing... (13 Replies)
Discussion started by: fossiili
13 Replies

13. UNIX for Beginners Questions & Answers

Grep command to show the number of results

Hi I wanted to know if there is an option in grep command to show the number of results (not the number of lines of findings). Thanks (14 Replies)
Discussion started by: abdossamad2003
14 Replies