atmarp(8) [debian man page]

ATMARP(8)						       Maintenance Commands							 ATMARP(8)

NAME

       atmarp - administer classical IP over ATM connections

SYNOPSIS

       atmarp -a
       atmarp -c [[atm]number]
       atmarp -q ip_addr [qos qos] [sndbuf bytes]
       atmarp -s ip_addr [itf.]vpi.vci [qos qos] [sndbuf bytes] [temp] [pub] [null]
       atmarp -s ip_addr atm_addr [qos qos] [sndbuf bytes] [temp] [pub] [arpsrv]
       atmarp -d ip_addr [arpsrv]
       atmarp -V

DESCRIPTION

       atmarp is used to maintain the ATMARP table of the ATMARP demon.  The table can be listed, new PVC and SVC entries can be added, and exist-
       ing entries can be deleted. In addition to that, atmarp is also used to create new IP over ATM interfaces.

       Note that the kernel has its own ATMARP table containing only entries for destinations to which a connection exists. The table  of  atmarpd
       can also contain currently unused entries.

OPTIONS

       -a     list the current ATMARP table.

       -c     create  the specified IP interface. If the interface number is omitted, the operating system assigns the next free number and atmarp
	      prints the resulting interface name (e.g. `atm0') on standard output.

       -q     sets the QOS and the send buffer size to use as the default for all VCs generated for that IP network (ip_addr must be  the  address
	      of the network).

       -s     set up a PVC or create an SVC entry. The following options are recognized:

	      qos qos
		     uses the specified quality of service (see qos(7) for the syntax). UBR at link speed is used by default.

	      sndbuf bytes
		     tries to set the send buffer to the specified number of bytes. A system default value is used if sndbuf is not specified.

	      temp   does not mark the entry as permanent, i.e. it will time out and then be removed.

	      pub    publishes	the  entry  (only  relevant  for  ATMARP  server).  ATMARP requests for entries not marked for publishing yield an
		     ATMARP_NAK response.

	      null   uses NULL encapsulation instead of LLC/SNAP encapsulation on the PVC. This option is not  available  for  SVCs,  because  the
		     LLC/SNAP header is required to identify ATMARP packets. null also implies that the entry is permanent.

	      arpsrv identifies the entry pointing to the ATMARP server. Note that the node acting as the ATMARP server must have no ATMARP server
		     entry in its ATMARP table.

       -d     delete the specified ARP entry.  In order to prevent accidental deletion of the ATMARP server entry, the arpsrv flag must be  speci-
	      fied when deleting it.

       -V     print the version number of atmarp on standard output and exit.

FILES

       /var/run/atmarpd.table	ATMARP table
AUTHOR

       Werner Almesberger, EPFL ICA <Werner.Almesberger@epfl.ch>
SEE ALSO

       atmarpd(8), clip(8), qos(7)

Linux								  April 26, 2000							 ATMARP(8)

Check Out this Related Man Page

ATMARPD(8)						       Maintenance Commands							ATMARPD(8)

NAME

       atmarpd - ATMARP demon

SYNOPSIS

       atmarpd [-b] [-d] [-D directory] [-l logfile] [-m] [-n]
       atmarpd -V

DESCRIPTION

       atmarpd	implements  the ATMARP protocol as specified in RFC1577 and RFC1755. Address resolution requests are sent from the kernel (using a
       comparably simple protocol) to the ATMARP demon, which then performs the dialog with the network.

       atmarpd can operate as an ATMARP client and as an ATMARP server.  If also supports the concurrent use of several IP over ATM interfaces.

       atmarpd is configured from the command line using the atmarp program. Unless debugging is enabled, the ATMARP table is written after  every
       change to the file /var/run/atmarpd.table (or to a file with the same name in a different directory, if the -D option is used).

       Note that atmarpd disables support for SVCs if signaling is not available at start time, i.e. if atmsigd is not running.

OPTIONS

       -b     Run in background (i.e. in a forked child process) after initializing.

       -d     Enables (lots of) debugging output. By default, atmarpd is comparably quiet.

       -D dump_dir
	      Changes the directory where atmarpd writes its table (atmarpd.table). By default, /var/run is used.

       -l logfile
	      Write diagnostic messages to the specified file instead of to standard error. The special name syslog is used to send diagnostics to
	      the system logger.

       -m     Enables merging of incoming calls if the address is known.  An incoming connection on which no InARP reply has  been  received  yet,
	      but  which  originates  from  an	ATM  address  for which an ATMARP entry already exists, is automatically added to that entry. This
	      assumes that there is a 1:1 mapping between IP addresses and ATMARP addresses. By default, this assumption is not made,  which  fre-
	      quently results in the setup of duplicate connections. Note that RFC1577 requires that an ATMARP server sends an InARP request on an
	      incoming connection. Merging may therefore violate RFC1577 in this case.

       -n     Prints addresses in numeric format only, i.e. no address to name translation is attempted.

       -V     Prints the version number of atmarpd on standard output and exits.

FILES

       /var/run/atmarpd.table	ATMARP table
       /proc/atm/arp		table of currently active IP over ATM VCs

BUGS

       atmarpd removes ATMARP entries from the kernel table while refreshing them.

AUTHOR

       Werner Almesberger, EPFL ICA <werner.almesberger@epfl.ch>

SEE ALSO

       atmarp(8), atmsigd(8)

Linux								  April 26, 2000							ATMARPD(8)

Linux and UNIX Man Pages

atmarp(8) [debian man page]

Check Out this Related Man Page