Linux and UNIX Man Pages

Linux & Unix Commands - Search Man Pages

config::model::models::lcdd::cfontzpacket(3pm) [debian man page]

Config::Model::models::LCDd::CFontzPacket(3pm)		User Contributed Perl Documentation	    Config::Model::models::LCDd::CFontzPacket(3pm)

NAME
Config::Model::models::LCDd::CFontzPacket - Configuration class LCDd::CFontzPacket VERSION
version 2.021 DESCRIPTION
Configuration classes used by Config::Model generated from LCDd.conf Elements Model Select the LCD model Optional. Type enum. choice: '533', '631', '633', '635'. upstream_default: '633'. Device Select the output device to use Optional. Type uniline. upstream_default: '/dev/lcd'. Contrast Set the initial contrast Optional. Type integer. upstream_default: '560'. Brightness Set the initial brightness Optional. Type integer. upstream_default: '1000'. OffBrightness Set the initial off-brightness This value is used when the display is normally switched off in case LCDd is inactive. Optional. Type integer. upstream_default: '0'. Reboot Reinitialize the LCD's BIOS on driver start. Optional. Type enum. choice: 'yes', 'no'. upstream_default: 'no'. USB Enable the USB flag if the device is connected to an USB port. For serial ports leave it disabled. Optional. Type enum. choice: 'yes', 'no'. upstream_default: 'no'. OldFirmware Very old 633 firmware versions do not support partial screen updates using 'Send Data to LCD' command(31). For those devices it may be necessary to enable this flag. Optional. Type enum. choice: 'yes', 'no'. upstream_default: 'no'. Size Override the LCD size known for the selected model. Usually setting this value should not be necessary.Optional. Type uniline. default: '20x4'. Speed Override the default communication speed known for the selected model. Default value depends on model Optional. Type enum. choice: '19200', '115200'. SEE ALSO
o cme perl v5.14.2 2012-11-09 Config::Model::models::LCDd::CFontzPacket(3pm)

Check Out this Related Man Page

Config::Model::models::LCDd::serialVFD(3pm)		User Contributed Perl Documentation	       Config::Model::models::LCDd::serialVFD(3pm)

NAME
Config::Model::models::LCDd::serialVFD - Configuration class LCDd::serialVFD VERSION
version 2.021 DESCRIPTION
Configuration classes used by Config::Model generated from LCDd.conf Elements Type Specifies the displaytype. 0 NEC (FIPC8367 based) VFDs. 1 KD Rev 2.1. 2 Noritake VFDs (*). 3 Futaba VFDs 4 IEE S03601-95B 5 IEE S03601-96-080 (*) 6 Futaba NA202SD08FA (allmost IEE compatible) 7 Samsung 20S207DA4 and 20S207DA6 8 Nixdorf BA6x / VT100 (* most should work, not tested yet.)Optional. Type uniline. upstream_default: '0'. use_parallel "no" if display connected serial, "yes" if connected parallel. I.e. serial by default. Optional. Type uniline. upstream_default: 'no'. Port Number of Custom-Characters. default is display type dependent Custom-Characters=0 Portaddress where the LPT is. Used in parallel mode only. Usual values are 0x278, 0x378 and 0x3BC.Optional. Type uniline. default: '0x378'. PortWait Set parallel port timing delay (us). Used in parallel mode only.Optional. Type integer. upstream_default: '2'. Device Device to use in serial mode. Usual values are /dev/ttyS0 and /dev/ttyS1. Optional. Type uniline. default: '/dev/ttyS1'. Size Specifies the size of the VFD.Optional. Type uniline. default: '20x2'. Brightness Set the initial brightness (4 steps 0-250, 251-500, 501-750, 751-1000)Optional. Type integer. upstream_default: '1000'. OffBrightness Set the initial off-brightness This value is used when the display is normally switched off in case LCDd is inactive (4 steps 0-250, 251-500, 501-750, 751-1000)Optional. Type integer. upstream_default: '0'. Speed set the serial port speed Optional. Type enum. choice: '1200', '2400', '9600', '19200', '115200'. upstream_default: '9600'. ISO_8859_1 enable ISO 8859 1 compatibility Optional. Type enum. choice: 'yes', 'no'. upstream_default: 'yes'. SEE ALSO
o cme perl v5.14.2 2012-11-09 Config::Model::models::LCDd::serialVFD(3pm)
Man Page

Featured Tech Videos