i want to kill a tcp connection by killing its pid
with netstat -an i got the tcp ip connection on port 5914
but when i type ps -a or ps-e there is not such process running on port 5914
is it possible that because i do not log on with proper user account i can not see that process running? (30 Replies)
Hi,
What iptables command do I need to run in order to open up the following port for incomming traffic on the following server:
# telnet 127.0.0.1 1521
Trying 127.0.0.1...
telnet: connect to address 127.0.0.1: Connection refused
telnet: Unable to connect to remote host: Connection... (3 Replies)
Dear All,
I have my HP Data Protector installed on the backup server.
I want to connect this backup server with the client server through
telnet port 5555 like below
telnet < ipaddress of client> 5555
But when I try like this , it says ...Connection refused ...unable to connect to... (0 Replies)
Dear members,
My release is open Solaris b103
1- How to know the opening port in my system
2- How to open a specific port like port number 53
3- How to closed the specific port like port number 53
Your feedback highly appreciated (10 Replies)
Hi. I ran nmap on my server, and I get the following:
Starting Nmap 4.76 ( http://nmap.org ) at 2009-03-19 16:33 EDT
Interesting ports on -------- (-----):
Not shown: 997 closed ports
PORT STATE SERVICE
22/tcp open ssh
80/tcp open http
6881/tcp open bittorrent-tracker
The... (0 Replies)
playing around with a command-line restore from omniback...anyone ever play with omnir?
I have the following test backup:
$ omnidb -session 2008/02/01-6
Object Name Object Type Object Status... (1 Reply)
Hi, Haveing a little trouble with data protector (5.5) on HP-UX (11.11, 11.23)
under Xwindows Chameleon UNIX 97 (7.0 - its a old version)
I am trying to get the GUI for DP up and running on a HP-UX cell manager and I have the following problem.
The GUI starts up with no errors that I can... (2 Replies)
TELNET-PROBE(1) General Commands Manual TELNET-PROBE(1)NAME
telnet-probe - lightweight telnet-like port probe
SYNOPSIS
$PCP_BINADM_DIR/telnet-probe [-c] [-v] host port
DESCRIPTION
telnet-probe allows the pmdashping(1) daemons to establish connections to arbitrary local and remote service-providing daemons so that
response time and service availability information can be obtained.
The required host and port number arguments have the same meaning as their telnet(1) equivalents.
The -c option causes telnet-probe to perform a connect(2) only. This skips the read(2) and write(2) exercise that would otherwise be done
after connecting (see below).
The -v option causes telnet-probe to be verbose while operating.
Once the telnet connection has been established, telnet-probe reads from stdin until end-of-file, and writes all the input data to the tel-
net connection. Next, telnet-probe will read from the telnet connection until end-of-file, discarding whatever data it receives. Then
telnet-probe exits.
To operate successfully, the input passed via telnet-probe to the remote service must be sufficient to cause the remote service to close
the connection when the last line of input has been processed, e.g. ending with ``quit'' when probing SMTP on port 25.
By default telnet-probe will not produce any output, unless there is an error in which case a diagnostic message can be displayed (in ver-
bose mode only) and the exit status will be non-zero indicating a failure.
PCP ENVIRONMENT
Environment variables with the prefix PCP_ are used to parameterize the file and directory names used by PCP. On each installation, the
file /etc/pcp.conf contains the local values for these variables. The $PCP_CONF variable may be used to specify an alternative configura-
tion file, as described in pcp.conf(5).
DIAGNOSTICS
If telnet-probe succeeds, then 0 will be returned. If the attempt to establish a connection fails or is terminated, then a non-zero exit
status is returned.
SEE ALSO PCPintro(1), pmdashping(1), pmie(1), telnet(1), connect(2), read(2) and write(2).
Performance Co-Pilot PCP TELNET-PROBE(1)
