routing rules for dmz in debian router.

4 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Debian As A Router [Not Assigning IPs]

I've been trying to set up an old desktop as a wifi router. I've looked at a lot of information online, but mostly this: https://seravo.fi/2014/create-wireless-access-point-hostapd I've gotten where I can see the ssid from my phone and laptop. However, it starts to connect, but never receives...

2. IP Networking

Dual Router (routing problem)

This is the network configuration I have: +-------------------------------------------------+ +===========+ | | | | | INTERNET |---| LINUXBOX2 | ...

3. UNIX for Dummies Questions & Answers

Remote Unix printing to my WinXP works with no router. How can I make it work through my router?

I set up remote printing on a clients Unix server to my Windows XP USB printer. My USB printer is connected directly to my PC (no print server and no network input on printer). With my Win XP PC connected to my cable modem (without the router), i can do lp -dhp842c /etc/hosts and it prints. I...

4. UNIX for Advanced & Expert Users

Firewall - 2 Internet accesses - routing rules from source

Hello, I would like to modify my firewall configuration for being able to handle 2 internet connections in my Red zone. I would then like to configure some selecting routing rules depending on the internal source. Actual configuration: ===================== 1 router A (ISP)...

LEARN ABOUT HPUX

mrinfo

mrinfo(1M)																mrinfo(1M)

NAME

       mrinfo - Multicast Routing Configuration Information Tool

SYNOPSIS

       debuglevel] retries] timeout] [ multicast-router ]

DESCRIPTION

       requests  the configuration information from the multicast-ourter, and prints the information to the standard out.  multicast-router can be
       either an IP address or a system name.  sends out the ASK_NEIGHBORS igmp  message  to  the  specified  multicast-router,  when  the  router
       receives  the request, it sends back its configuration information. If the multicast-router is not specified, the request is sent the local
       router.

       The the configuration information for each interface is printed in the following format:

       If there are multiple neighbor routers on one interface, they will all be reported on the output.  The possible values for flag are:

       Neighbors are reached via tunnel.

       The tunnel uses IP source routing.

       The interface is down.

       The interface is administratively disabled for multicast routing.

       The local router is the querier of the subnet.

       Please see mrouted(1M) for and

       The command line options are:

       Sets the level for printing out the debug message. The default is 0,
		     only error and warning messages will be printed. Debug level three prints most the messages.

       Sets the retry times to pull the routing daemon for information. The
		     default is 3.

       Specifies the timeout value in seconds for waiting the reply. The default value
		     is 4.

EXAMPLE

       The following is an example of quering the multicasting configuration from the local routing daemon.

	      127.0.0.1 (localhost) [version 3.3]:
		15.13.106.144 -> 15.13.106.145 (hpntcbs.cup.hp.com) [10/1/querier]
		193.2.1.39 -> 0.0.0.0 (all-zeros-broadcast) [1/1/disabled]
		15.13.106.144 -> 15.255.176.33 (matmos.hpl.hp.com) [10/1/tunnel]
		15.13.106.144 -> 15.17.20.7 (hpspddc.vid.hp.com) [10/1/tunnel/down]

   Note
       must be run as root.

AUTHOR

       was developed by Van Jacobson.

SEE ALSO

       mrouted(1M), map-mbone(1M).

																	mrinfo(1M)

Linux