10 More Discussions You Might Find Interesting
1. Red Hat
I have a couple of questions regarding multipath.
If I do vgdisplay vg01, I see it is using 1 PV: /dev/dm-13
If I type multipath -ll I see dm-9, dm-10, dm-11, dm-12, but do not see dm-13. Is my vg01 multipathed? How can I actually know for sure?
Secondly, let's say this time vg01 says... (1 Reply)
Discussion started by: keelba
1 Replies
2. Linux
Hi folks.
When issuing a multipath -ll on my server, i see something that is bugging me...
# multipath -ll
2000b0803ce002582 dm-10 Pillar,Axiom 600
size=129G features='0' hwhandler='0' wp=rw
|-+- policy='round-robin 0' prio=50 status=active
| |- 0:0:0:4 sdd 8:48 active ready running... (0 Replies)
Discussion started by: Stephan
0 Replies
3. AIX
Hi,
I know the concept of multipathing, but would like to know how to configure multipathing in AIX.
or software/driver is by default present in AIX??????
How to find out wheather multipathing is configured in AIX?????
Regards,
Manu (4 Replies)
Discussion started by: manoj.solaris
4 Replies
4. Red Hat
I have a server running redhat 5.5 and it has one SAN device presented to it as LUN9. How can I clean up the remaining entries. I cannot afford to interupt the service. Please assist.
# multipath -l
mpath0 (36000097000019260298953666633436) dm-11 EMC,SYMMETRIX
\_ round-robin 0
\_ 2:0:0:9 ... (2 Replies)
Discussion started by: Tirmazi
2 Replies
5. Solaris
Hello,
I turned on the server multipathing:
# uname -a
SunOS caiman 5.10 Generic_141444-09 sun4v sparc SUNW,T5140
stmsboot -D fp -e
And after a reboot the server, multipathing is not enable:
# stmsboot -L
stmsboot: MPxIO is not enabled
stmsboot: MPxIO disabled
# ls /dev/dsk... (4 Replies)
Discussion started by: bieszczaders
4 Replies
6. Solaris
Hai
we using emc storage which is conneted to M5000 through san switch.
we asign 13 luns but in server it is showing 22 luns.
i enable the solaris multipathing (MPxIO)
#more /kernel/drv/fp.conf in that file
MPxio-disable=no
#mpathadm list lu
it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I've been asked to setup disk multipathing (not IP multipathing) I have searched the internet and found limited documents, I have found one
http://dlc.sun.com/pdf/819-0139-12/819-0139-12.pdf but I am struggling to understand it.
Does anyone have any links I can use that will tell me... (2 Replies)
Discussion started by: newbiesolaris10
2 Replies
8. AIX
Hello guys
as i new to AIX i need to know is there any virtual system for AIX i want to practice and i don have IBM machine !!!
any help (4 Replies)
Discussion started by: F_A_H_D
4 Replies
9. Solaris
Hi,
I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation .
I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2.
Now is it possible to have IP Multipathing on each of the servers as follows ?
... (0 Replies)
Discussion started by: maadhuu
0 Replies
10. Solaris
I have solaris 10 sparc. I installed a Qlogic hba card.
This card is connected on a brocade switch and the brocade is connected on 2 different controllers on a Hitachi disk bay.
I formated 2 luns. On my solaris system, i have 4 disk.
How to configure solaris 10 to fix the dual disk view.
... (4 Replies)
Discussion started by: simquest
4 Replies