10 More Discussions You Might Find Interesting
1. Emergency UNIX and Linux Support
Hi guys.
I have downloaded kernel 2.6.38-5 to add a system call.
I did the following steps:
1. I have added my system call to system call table
<src folder>/arc/x86/kernel/syscall_table_32.S
.long sys_mycall
2. i have added the system cal number in
<src... (5 Replies)
Discussion started by: majid.merkava
5 Replies
2. Shell Programming and Scripting
Hi
I am trying to create a script extracting the IP provided by ifconfig.
I tried with grep + awk but I am returned more than I need.
/sbin/ifconfig eth0 | grep "inet addr:" | awk '/inet addr:/ { print $2 }'
and returns
addr:10.15.1.64
How can I remove "addr:" string?... (9 Replies)
Discussion started by: manustone
9 Replies
3. Solaris
hi,
I am trying to configure one of my interfaces, but after reboot - i lose the changes to the netmask & broadcast address.
I have added an entry in /etc/netmasks, but it doesnt pick up the new settings. any ideas - much appreciated.
before reboot:
eri0:... (3 Replies)
Discussion started by: badoshi
3 Replies
4. IP Networking
I'm working on an AIX Unix LPAR (AIX 3.5 00C3C9904C00 as returned by uname -a)
I can access this box using telnet, port 22 using adress IP A and B
A=AA.AA.XX.XX and B=AA.AA.YYY.YYY
I can confirm these 2 are the same space, I can see
I can't find address B listed anywhere... so I wonder what... (1 Reply)
Discussion started by: Isax50
1 Replies
5. Shell Programming and Scripting
I'm a newbie to linux, so pleases forgive me!
I would like to find a script that I could use to extract a dynamic ip from the ppp0 and set it as a variable to be used in IPTables
basically, if ppp0 ip address is 10.10.10.20, I would like a script that would set a var to 10.10.10.0. of... (9 Replies)
Discussion started by: speedy3k
9 Replies
6. Shell Programming and Scripting
Hello All,
Can someone show me how to cat "only the IP address of e1000g0" using ifconfig -a.
i am trying to grep only the ip address (xx.xx.xx.xx) from the bunch of all other things like, broadcast address, IPV4, UP........and so on.
thanks (1 Reply)
Discussion started by: solaix14
1 Replies
7. Shell Programming and Scripting
hi,
i want to know how to grep inet address for below
below is the output of ifconfig command
/home/JA> ifconfig
eth0 Link encap:Ethernet HWaddr 00:11:0A:5B:2E:E9
inet addr:161.239.203.18 Bcast:161.239.203.127 Mask:255.255.255.128
UP BROADCAST RUNNING... (3 Replies)
Discussion started by: mail2sant
3 Replies
8. IP Networking
I am trying to write a C server code that will handle WWW request from client. i am very new to socket programming. i can very well setup the socket...but when an incomin request comes from a browser, the progrom exits with an error message "Bad address". the following is the code. please do help... (1 Reply)
Discussion started by: shankarramv
1 Replies
9. IP Networking
Hello,
I have a server with two ip addresses. I need to make the ip address that's currently the secondary the primary. How do I use the ifconfig command and primary option?
Thanks. (5 Replies)
Discussion started by: pmichner
5 Replies
10. Solaris
hi all
iam trying to set my eri0 interface but with little luck .
when i set the ip using ipconfig i always get "bad adress"..
moreover when i use ifconfig eri0 i can notice that the inet is 0.0.0.0 and the netmask 0
i am runnig solaris 9 on sparc .
any helpis highly appreciated ... ... (2 Replies)
Discussion started by: ppass
2 Replies