Sponsored Content
Special Forums IP Networking ifconfig: ce401001: bad address Post 302203011 by DukeNuke2 on Friday 6th of June 2008 10:53:19 AM
Old 06-06-2008
the card has a vlan "tag". i don't now how to treat such an interface (no experience) but maybe you can find something usefull in the "ifconfig" manpage when you search for vlan...

hth,
DN2
 

10 More Discussions You Might Find Interesting

1. Solaris

ifconfig bad address

hi all iam trying to set my eri0 interface but with little luck . when i set the ip using ipconfig i always get "bad adress".. moreover when i use ifconfig eri0 i can notice that the inet is 0.0.0.0 and the netmask 0 i am runnig solaris 9 on sparc . any helpis highly appreciated ... ... (2 Replies)
Discussion started by: ppass
2 Replies

2. IP Networking

Setting primary ip address with ifconfig

Hello, I have a server with two ip addresses. I need to make the ip address that's currently the secondary the primary. How do I use the ifconfig command and primary option? Thanks. (5 Replies)
Discussion started by: pmichner
5 Replies

3. IP Networking

Bad Address

I am trying to write a C server code that will handle WWW request from client. i am very new to socket programming. i can very well setup the socket...but when an incomin request comes from a browser, the progrom exits with an error message "Bad address". the following is the code. please do help... (1 Reply)
Discussion started by: shankarramv
1 Replies

4. Shell Programming and Scripting

how grep the inet address for in ifconfig command

hi, i want to know how to grep inet address for below below is the output of ifconfig command /home/JA> ifconfig eth0 Link encap:Ethernet HWaddr 00:11:0A:5B:2E:E9 inet addr:161.239.203.18 Bcast:161.239.203.127 Mask:255.255.255.128 UP BROADCAST RUNNING... (3 Replies)
Discussion started by: mail2sant
3 Replies

5. Shell Programming and Scripting

how to grep only IP address of e1000g0 using ifconfig -a

Hello All, Can someone show me how to cat "only the IP address of e1000g0" using ifconfig -a. i am trying to grep only the ip address (xx.xx.xx.xx) from the bunch of all other things like, broadcast address, IPV4, UP........and so on. thanks (1 Reply)
Discussion started by: solaix14
1 Replies

6. Shell Programming and Scripting

script to get IP address from ifconfig

I'm a newbie to linux, so pleases forgive me! I would like to find a script that I could use to extract a dynamic ip from the ppp0 and set it as a variable to be used in IPTables basically, if ppp0 ip address is 10.10.10.20, I would like a script that would set a var to 10.10.10.0. of... (9 Replies)
Discussion started by: speedy3k
9 Replies

7. IP Networking

IP Address not found in ifconfig/netstat

I'm working on an AIX Unix LPAR (AIX 3.5 00C3C9904C00 as returned by uname -a) I can access this box using telnet, port 22 using adress IP A and B A=AA.AA.XX.XX and B=AA.AA.YYY.YYY I can confirm these 2 are the same space, I can see I can't find address B listed anywhere... so I wonder what... (1 Reply)
Discussion started by: Isax50
1 Replies

8. Solaris

ifconfig - making netmask & broadcast address permanent?

hi, I am trying to configure one of my interfaces, but after reboot - i lose the changes to the netmask & broadcast address. I have added an entry in /etc/netmasks, but it doesnt pick up the new settings. any ideas - much appreciated. before reboot: eri0:... (3 Replies)
Discussion started by: badoshi
3 Replies

9. Shell Programming and Scripting

extracting the ip address from ifconfig

Hi I am trying to create a script extracting the IP provided by ifconfig. I tried with grep + awk but I am returned more than I need. /sbin/ifconfig eth0 | grep "inet addr:" | awk '/inet addr:/ { print $2 }' and returns addr:10.15.1.64 How can I remove "addr:" string?... (9 Replies)
Discussion started by: manustone
9 Replies

10. Emergency UNIX and Linux Support

Bad Address when adding system call

Hi guys. I have downloaded kernel 2.6.38-5 to add a system call. I did the following steps: 1. I have added my system call to system call table <src folder>/arc/x86/kernel/syscall_table_32.S .long sys_mycall 2. i have added the system cal number in <src... (5 Replies)
Discussion started by: majid.merkava
5 Replies
VLAN(4) 						   BSD Kernel Interfaces Manual 						   VLAN(4)

NAME
vlan -- IEEE 802.1Q VLAN network interface SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device vlan Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_vlan_load="YES" DESCRIPTION
The vlan driver demultiplexes frames tagged according to the IEEE 802.1Q standard into logical vlan network interfaces, which allows rout- ing/bridging between multiple VLANs through a single switch trunk port. Each vlan interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using the cloned_interfaces variable in rc.conf(5). To function, a vlan interface must be assigned a parent interface and numeric VLAN tag using ifconfig(8). A single parent can be assigned to multiple vlan interfaces provided they have different tags. The parent interface is likely to be an Ethernet card connected to a properly configured switch port. The VLAN tag should match one of those set up in the switched network. Initially vlan assumes the same minimum length for tagged and untagged frames. This mode is selected by the sysctl(8) variable net.link.vlan.soft_pad set to 0 (default). However, there are network devices that fail to adjust frame length, should it fall below the allowed minimum due to untagging. Such devices should be able to interoperate with vlan after changing the value of net.link.vlan.soft_pad to 1. In the latter mode, vlan will pad short frames before tagging them so that their length stays not less than the minimum value after untagging by the non-compliant devices. HARDWARE
The vlan driver supports efficient operation over parent interfaces that can provide help in processing VLANs. Such interfaces are automati- cally recognized by their capabilities. Depending on the level of sophistication found in a physical interface, it may do full VLAN process- ing or just be able to receive and transmit long frames (up to 1522 bytes including an Ethernet header and FCS). The capabilities may be user-controlled by the respective parameters to ifconfig(8), vlanhwtag and vlanmtu. However, a physical interface is not obliged to react to them: It may have either capability enabled permanently without a way to turn it off. The whole issue is very specific to a particular device and its driver. By now, the list of physical interfaces able of full VLAN processing in the hardware is limited to the following devices: ae(4), age(4), alc(4), ale(4), bce(4), bge(4), cxgb(4), em(4), ixgb(4), jme(4), msk(4), nge(4), re(4), sge(4), stge(4), ti(4), txp(4), and vge(4). The rest of the Ethernet interfaces can run VLANs using software emulation in the vlan driver. However, some of them lack the capability of transmitting and receiving long frames. Assigning such an interface as the parent to vlan will result in a reduced MTU on the corresponding vlan interfaces. In the modern Internet, this is likely to cause tcp(4) connectivity problems due to massive, inadequate icmp(4) filtering that breaks the Path MTU Discovery mechanism. The following interfaces support long frames for vlan natively: bfe(4), cas(4), dc(4), fwe(4), fxp(4), gem(4), hme(4), le(4), nfe(4), nve(4), rl(4), sf(4), sis(4), sk(4), ste(4), tl(4), tx(4), vr(4), and xl(4). The vlan driver automatically recognizes devices that natively support long frames for vlan use and calculates the appropriate frame MTU based on the capabilities of the parent interface. Some other interfaces not listed above may handle long frames, but they do not advertise this ability of theirs. The MTU setting on vlan can be corrected manually if used in conjunction with such a parent interface. SEE ALSO
ifconfig(8), sysctl(8) BUGS
No 802.1Q features except VLAN tagging are implemented. BSD
April 14, 2010 BSD
All times are GMT -4. The time now is 02:21 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy