Need help configuring Cisco 892-k9 router


 
Thread Tools Search this Thread
Special Forums IP Networking Need help configuring Cisco 892-k9 router
# 1  
Old 12-16-2015
Need help configuring Cisco 892-k9 router

I bought a Cisco 892-k9 router and I am having in issue trying to setup the initial configuration. Does someone have a sampl configuration for a single subnet that I can use for my configuration?

Thanks.
Login or Register to Ask a Question

Previous Thread | Next Thread

8 More Discussions You Might Find Interesting

1. IP Networking

Does cisco 1921 router support site to site VPNs using IPSec?

Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? " A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Discussion started by: Ayaerlee
0 Replies

2. IP Networking

How to show Cisco Router Running Configuration in Third Party Application

Hey everyone, I have a few question. 1. Is it possible to display cisco 'show run' output command to the application ?? 2. And is there any ways to log in to the router instead of using telnet from telnet application??? Thanks in advance (0 Replies)
Discussion started by: franzramadhan
0 Replies

3. IP Networking

isc dhcpd and cisco router

Hello all, I have set up dhcpd on a linux box for serving subnets on multiple vlans configured on a Cisco 6500 with ip helper of the dhcp server. Servers get dhcp leases just fine, however, some machines lose their connection for reboot or what not and I can not get their lease back even though... (0 Replies)
Discussion started by: closedown
0 Replies

4. IP Networking

Setup Dial In VPN on Cisco Router

Hello, Does anyone know where I can find configuration information on setting up a dial in VPN on Cicso IOS for a bunch of servers. Could not seem to find anything in search engines. Thanks (0 Replies)
Discussion started by: photon
0 Replies

5. IP Networking

how Configuring zebra router as/for NBMA netwoks

I have a zebra router configured....which is working correctly......But I want zebra to not send the data to multicast address 224.0.0.5.....but directly only to my IP...Is there a way to do this....I read that in NBMA networks the message are not sent to the multicast address. Any idea or any... (2 Replies)
Discussion started by: cosmic_egg
2 Replies

6. IP Networking

Linux behind a cisco router

Dear All, I have worked with xDSL routers working in bridged mode, and linux behind them working as a Firewall utilizing IPTABLES. My question is, how this will change if the xDSL router is replaced with a Cisco Router? I mean to ask that, can I assign a public ip on the linux machine, which... (0 Replies)
Discussion started by: tmm
0 Replies

7. Shell Programming and Scripting

Perl telnet to cisco router and compare the ping ms

All Please help, i will telnet to router to obain the ping status and compare, if higher than normal latency, i will have further action.. if i do the telent and in perl script then .... e.g the result i obtain from the router will be =' Success rate is 100 percent (5/5), round-trip... (4 Replies)
Discussion started by: optimus
4 Replies

8. UNIX for Advanced & Expert Users

Cisco Router command to get hostname

Hi All, I am connected to a cisco router and I want to know the hostname of this router. I connect as telnet <IPADDRESS> and the prompt shows vpnaccess-bristol> But I want to know the full hostname of the router how can i do that. When i type the hostname command the following... (3 Replies)
Discussion started by: rahulrathod
3 Replies
Login or Register to Ask a Question
mrinfo(1M)																mrinfo(1M)

NAME
mrinfo - Multicast Routing Configuration Information Tool SYNOPSIS
debuglevel] retries] timeout] [ multicast-router ] DESCRIPTION
requests the configuration information from the multicast-ourter, and prints the information to the standard out. multicast-router can be either an IP address or a system name. sends out the ASK_NEIGHBORS igmp message to the specified multicast-router, when the router receives the request, it sends back its configuration information. If the multicast-router is not specified, the request is sent the local router. The the configuration information for each interface is printed in the following format: If there are multiple neighbor routers on one interface, they will all be reported on the output. The possible values for flag are: Neighbors are reached via tunnel. The tunnel uses IP source routing. The interface is down. The interface is administratively disabled for multicast routing. The local router is the querier of the subnet. Please see mrouted(1M) for and The command line options are: Sets the level for printing out the debug message. The default is 0, only error and warning messages will be printed. Debug level three prints most the messages. Sets the retry times to pull the routing daemon for information. The default is 3. Specifies the timeout value in seconds for waiting the reply. The default value is 4. EXAMPLE
The following is an example of quering the multicasting configuration from the local routing daemon. 127.0.0.1 (localhost) [version 3.3]: 15.13.106.144 -> 15.13.106.145 (hpntcbs.cup.hp.com) [10/1/querier] 193.2.1.39 -> 0.0.0.0 (all-zeros-broadcast) [1/1/disabled] 15.13.106.144 -> 15.255.176.33 (matmos.hpl.hp.com) [10/1/tunnel] 15.13.106.144 -> 15.17.20.7 (hpspddc.vid.hp.com) [10/1/tunnel/down] Note must be run as root. AUTHOR
was developed by Van Jacobson. SEE ALSO
mrouted(1M), map-mbone(1M). mrinfo(1M)