9 More Discussions You Might Find Interesting
1. Solaris
Hey there,
I joined this forum just now cause I need help with an old SUN machine at work. I work on a helpdesk and we use a SOLARIS 5.10 OS. Every once in a while we will try to move one of our windows out of the way to make room on the desktop, and sometimes the mouse doesn't release what we... (7 Replies)
Discussion started by: TRex_2005
7 Replies
2. Linux
Hi all,
OS: fedora release 10
when i try to restart network service, ending up with following errors. There are two interfaces eth0 and eth1
bringing up interface eth0 rtnetlink answers file exists
error adding <IP Address here> to eth0
bringing up interface eth0 rtnetlink answers... (2 Replies)
Discussion started by: lramsb4u
2 Replies
3. BSD
Hi Experts,
I am executing "svn" checkout command through my java code on a freeBSD machine. SVN checkout gets started , but when I run "top" command on my freebsd machine, I have observed that "svn" processes are stuck in "pipewr" state.
Any pointer for this problem?
Thanks,
akash (0 Replies)
Discussion started by: akash.mahakode
0 Replies
4. UNIX for Advanced & Expert Users
Hi Experts,
I am executing "svn" checkout command through my java code on a freeBSD machine. SVN checkout gets started , but when I run "top" command on my freebsd machine, I have observed that "svn" processes are stuck in "pipewr" state.
Any pointer for this problem?
Thanks,
akash (0 Replies)
Discussion started by: akash.mahakode
0 Replies
5. Shell Programming and Scripting
Hi,
I have line in input file as below:
3G_CENTRAL;INDONESIA_(M)_TELKOMSEL;SPECIAL_WORLD_GRP_7_FA_2_TELKOMSEL
My expected output for line in the file must be :
"1-Radon1-cMOC_deg"|"LDIndex"|"3G_CENTRAL|INDONESIA_(M)_TELKOMSEL"|LAST|"SPECIAL_WORLD_GRP_7_FA_2_TELKOMSEL"
Can someone... (7 Replies)
Discussion started by: shis100
7 Replies
6. AIX
Hi
I was wondering if anybody has come across in a failure of fuser command.
We have a backup script that is:
fuser -c -k /XXX/XXXXXXX
sync;sync
umount /XXX/XXXXXXX/
backup -0 -f /dev/rmt0.1 -u /dev/XXXXXXXlv
mount /XXX/XXXXXXX/
sync;sync
The script is called from crontab via an... (2 Replies)
Discussion started by: ggovotsis
2 Replies
7. Solaris
On Solaris 8, when I do a lpstat -o:
I have tried cancel 140828p-16974, but the entries remain
New prints to this printer and others work successfully.
Can anyone suggest how to get rid of these entries.
Thanks (2 Replies)
Discussion started by: pmm
2 Replies
8. AIX
Good afternoon,
I'm currently working on an IBM 9110-510, with an AIX 6.1 on it.
Currently, I've put an HyperTerminal on the machine vty0. Folowing the procedure given by a support guy(§details), I'm able to get to the AIX banner
... (6 Replies)
Discussion started by: nilleb
6 Replies
9. UNIX for Advanced & Expert Users
HI,
When I do 'service network restart' , I am getting the following error.
"3c501 device eth0 does not seem to be present, delaying initialization"
Can any one suggest me the cause/solution for this?
When I do 'lspci' it is showing the ehternet card as
" Ethernet controller"Marvell... (2 Replies)
Discussion started by: praveen_b744
2 Replies
IFSYSCTL(5) Network configuration IFSYSCTL(5)
NAME
ifsysctl[-<interface name>] - per network interface sysctl settings
SYNOPSIS
/etc/sysconfig/network/ifsysctl
/etc/sysconfig/network/ifsysctl-<interface name>
DESCRIPTION
These files are intended to contain sysctl settings, that should be applied when a network interface is created. This are usually interface
specific settings, like:
net.ipv6.conf.eth0.use_tempaddr = 1
or
net.ipv4.conf.eth0.rp_filter = 0
The settings are applied by the /etc/sysconfig/network/scripts/ifup-sysctl script executed via /etc/udev/rules.d/77-network.rules rule (see
udev(7)), after the creation and after the rename of the interface name to its persistent name (when applicable), but before the ifup
<interface name> -o hotplug may be executed to configure the interface.
The settings are not applied by default when the NetworkManager is active (NETWORKMANAGER=yes), except when the IFSYSCTL_NETWORKMANAGER=yes
variable is set in the /etc/sysconfig/network/config file.
Settings from the ifsysctl- file are applied every time an interface has been created.
Settings from the ifsysctl-interface name file are applied when the interface with the corresponding interface name has been created.
SYNTAX
The sysctl(8) utility is required to apply the settings. It supports two separator characters for sysctl keywords: a "." in default format
and a "/" in the alternate format. Therefore the syntax is basically same to the /etc/sysctl.conf file.
Interface names may contain a ".". In the default sysctl format using a "." as separator, that is any "." in the interface name of the key-
word, has to be replaced with a "/". In the alternate sysctl format with "/" as separator, normal interface names can be used.
Optionally, the ifsysctl files may contain also the $INTERFACE and the $SYSCTL_IF variables, that are automatically replaced with the cur-
rent interface name usable in the alternate format and with the sysctl-quoted interface name for the default format, before the settings
are passed to the sysctl utility.
Note also, that settings with variables in the ifsysctl (without the -<interface name> suffix), will be applied for every interface!
Further, files with variables are not compatible to the /etc/sysctl.conf file.
EXAMPLES
Settings for "eth0" and "eth0.1" interfaces
# using "." as separator:
net.ipv6.conf.eth0.use_tempaddr = 1
net.ipv6.conf.eth0/1.use_tempaddr = 1
# using "/" as separator:
net/ipv6/conf/eth0/use_tempaddr = 1
net/ipv6/conf/eth0.0/use_tempaddr = 1
Settings with variables:
# using "." as separator:
net.ipv6.conf.$SYSCTL_IF.use_tempaddr = 1
# using "/" as separator:
net/ipv6/conf/$INTERFACE/use_tempaddr = 1
To test your ifsysctl-eth0 or ifsysctl file, use:
/etc/sysconfig/network/scripts/ifup-sysctl eth0 -o debug
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO
ifup(8) ifcfg(5) sysctl(8)
sysconfig December 2009 IFSYSCTL(5)