10 More Discussions You Might Find Interesting
1. Hardware
Dear all,
I am setting up a new Ethernet network at home, I am going to have a good 100 Mbps internet connection (optic fiber) with a modem that have a gigabit ethernet card.
I would like to to measure the speed of data transmission between several servers that are going to be connected to the... (2 Replies)
Discussion started by: freddie50
2 Replies
2. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
3. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
4. Solaris
Hi Group,
I Have just installed quad card in my V440 machine,
I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able,
here is details of my machine.
ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index
1
... (2 Replies)
Discussion started by: sameergrover
2 Replies
5. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
6. Solaris
I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me:
SIOCSLIFFLAGS:... (5 Replies)
Discussion started by: hshapiro
5 Replies
7. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
8. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
9. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
10. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
LAST(1) BSD General Commands Manual LAST(1)
NAME
last -- indicate last logins of users and ttys
SYNOPSIS
last [-n] [-h host] [-t tty] [user ...]
DESCRIPTION
Last will list the sessions of specified users, ttys, and hosts, in reverse time order. Each line of output contains the user name, the tty
from which the session was conducted, any hostname, the start and stop times for the session, and the duration of the session. If the ses-
sion is still continuing or was cut short by a crash or shutdown, last will so indicate.
-n Limits the report to n lines.
-h host Host names may be names or internet numbers.
-t tty Specify the tty. Tty names may be given fully or abbreviated, for example, ``last -t 03'' is equivalent to ``last -t tty03''.
If multiple arguments are given, the information which applies to any of the arguments is printed, e.g., ``last root -t console'' would list
all of ``root's'' sessions as well as all sessions on the console terminal. If no users, hostnames or terminals are specified, last prints a
record of all logins and logouts.
The pseudo-user reboot logs in at reboots of the system, thus ``last reboot'' will give an indication of mean time between reboot.
If last is interrupted, it indicates to what date the search has progressed. If interrupted with a quit signal last indicates how far the
search has progressed and then continues.
SEE ALSO
lastcomm(1), utmpx(5), ac(8)
HISTORY
Last appeared in 3.0BSD.
4th Berkeley Distribution June 6, 1993 4th Berkeley Distribution