10 More Discussions You Might Find Interesting
1. Red Hat
Dear All ,
Very recently we have configured Network bonding in our Linux Server Redhat Linux 5.x.
After configuring , we restarted the network services , the link was down after that , we could not login in to the Server.
So after that , we logged in to console and tried to... (2 Replies)
Discussion started by: jegaraman
2 Replies
2. Red Hat
I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
Discussion started by: Anjan Ganguly
4 Replies
3. IP Networking
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Discussion started by: elliottlc
0 Replies
4. Red Hat
Does anyone know if it's possible to bond two bonds together? My situation is I have two older Cisco switches that cannot carry a LACP (bond level 4) aggregated between them, but separate aggregates can be setup on the switches themselves. In order to have redundancy of two switches I would... (0 Replies)
Discussion started by: christr
0 Replies
5. Red Hat
I am new to linux. I have a falconstor CDP installation which runs on RHEL 5.5 (Tikanga). There is a vendor option to bond nics in either 802.3ad or round robin, I choose 802.3ad. The server is connected to a Cisco 3750 switch.
The problem is dropped packets and eth03 wont come up in the PO... (0 Replies)
Discussion started by: tjcooper
0 Replies
6. Linux
I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
alias bond0 bonding
options bonding... (2 Replies)
Discussion started by: dr_mabuse
2 Replies
7. Red Hat
Hi,
What is IP bonding in Linux.
What are its advantages
How to create a IP bonding in redhat Linux. (1 Reply)
Discussion started by: chetansingh23
1 Replies
8. IP Networking
I’m familiar with load balancing.. but Is it possible to actually bond multiple DSL lines together? I hear of ways to bond using MLPPP but that requires support from an ISP. Is there a way to actually bond without support from my ISP, or use say a cable modem and a DSL line together for faster... (0 Replies)
Discussion started by: harley313
0 Replies
9. HP-UX
userA and userB are two non-root accounts on HP-UX box. userA creates ssh tunnel (local forward) to some different host. Will userB be able to use that tunnel? What about remote forward? If not, what OS mechanism will prevent it from happening? Unfortunately I am unable to create this setup at this... (0 Replies)
Discussion started by: vkleban
0 Replies
10. UNIX for Advanced & Expert Users
Here is the scenario:
I use an OpenBSD 2.9 box as my firewall and gateway at the house. One of the boxes behind my OpenBSD box is my FreeBSDBox.
I would like to be able to use port forwarding with SSH to enable a secure connection from work to the OpenBSD box and to have the OpenBSD box... (6 Replies)
Discussion started by: auswipe
6 Replies
AICCU(1) AICCU(1)
NAME
AICCU - Automatic IPv6 Connectivity Configuration Utility
SYNOPSIS
aiccu <start|stop|tunnels|test|autotest|license> [ config ]
DESCRIPTION
AICCU makes it very easy for anybody to get IPv6 connectivity everywhere they want. It uses the TIC (Tunnel Information & Control) protocol
to request the information needed to setup a tunnel through which the connectivity is created. AICCU supports the following tunneling pro-
tocols: - 6in4 static (RFC 2893) - 6in4 heartbeat (RFC 2893 + draft-massar-v6ops-heartbeat) - tinc (http://www.tinc-vpn.org) -
AYIYA (draft-massar-v6ops-ayiya) As AYIYA even works from behind NAT's, thus unless there is a very restrictive firewall in place,
anybody should be able to get IPv6 connectivity without problems and everywhere they want.
OPTIONS
start Starts aiccu service.
stop Stops aiccu service.
tunnels
Prints a list of currently available tunnels.
test Builds the connection and runs a simple selftest allowing a user to report this back as it should show most obvious problems.
autotest
Decription here
license
Shows the license aiccu is released under.
config Read the configuration from config file.
SEE ALSO
The AICCU page <URL:http://www.sixxs.net/tools/aiccu/> at sixxs.
AUTHOR
AICCU was written by Jeroen Massar with contributions supplied a number of people as mentioned in the Changelog.
18 April 2005 AICCU(1)