10 More Discussions You Might Find Interesting
1. IP Networking
Server is stuck at "Stuck at "bringing up interface eth0:""
after i hard reset the server
I have IPMI access, please help me diagnose the cause if you can :( (0 Replies)
Discussion started by: postcd
0 Replies
2. UNIX for Dummies Questions & Answers
hi guys
I have a server which has 2 nics eth0 and eth1
eth0 is used for our email traffic server. everything working fine
some time later a eth1 was added for backup purposes so this new nic sends data to another vlan for backup purposes
all of a sudden our mail server starts to fail... (3 Replies)
Discussion started by: karlochacon
3 Replies
3. Red Hat
Hi,
I´ve given only this info to configure a network interface : "port 1 PCI 4"
I´ve been searching for any kind of relationship in the system which allow me to find the etc that must be configured...
Please, could anybody help me?
rhxx:#/root# lspci |grep -i "PCI BRIDGE"
00:01.0 PCI... (0 Replies)
Discussion started by: pabloli150
0 Replies
4. Linux
Hi all,
OS: fedora release 10
when i try to restart network service, ending up with following errors. There are two interfaces eth0 and eth1
bringing up interface eth0 rtnetlink answers file exists
error adding <IP Address here> to eth0
bringing up interface eth0 rtnetlink answers... (2 Replies)
Discussion started by: lramsb4u
2 Replies
5. Shell Programming and Scripting
I want to run dhcpclient for all the eth* which has no ip
for example
eth0 Link encap:Ethernet HWaddr 00:1E:67:3E:BA:EF
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0... (6 Replies)
Discussion started by: yanglei_fage
6 Replies
6. IP Networking
Hello everybody,
I have been reading many posts about this topic but I have no figure out how to solve it.
I need to split the traffic incoming on eth0 on two other interfaces (for instance one receiving on port 80 and the others on the other interface).
I cannot understand how to do that.... (2 Replies)
Discussion started by: nicandro
2 Replies
7. UNIX for Advanced & Expert Users
Hi,
For one of my application(Linux 2.6) I am using a netlink socket to get the interface changes notification.
socket(PF_NETLINK, SOCK_RAW, NETLINK_ROUTE)
Application receives netlink notification for Ethernet, bond interfaces but there is no notification about bridge interfaces changes. ... (6 Replies)
Discussion started by: learn more
6 Replies
8. UNIX for Dummies Questions & Answers
folks;
This might sounds stupid but i hope someone can give me an answer:
On my Linux SUSE boxes, i have 2 NIC cards NIC1 & NIC2. I always assumed that NIC1 is eth0 when i run "ifconfig" and NIC2 is eth1
but i noticed that's not always the case.
Is there a way or a command i can run to find... (1 Reply)
Discussion started by: Katkota
1 Replies
9. Linux
Hi
I had a DL380 with two two port eth cards. I now replaced one with a four port eth card and my interfaces seemed to have jumped around.
Is there a method of moving eth ports... eg making port eth4 eth2.:confused: (2 Replies)
Discussion started by: theroncj
2 Replies
10. UNIX for Advanced & Expert Users
HI,
When I do 'service network restart' , I am getting the following error.
"3c501 device eth0 does not seem to be present, delaying initialization"
Can any one suggest me the cause/solution for this?
When I do 'lspci' it is showing the ehternet card as
" Ethernet controller"Marvell... (2 Replies)
Discussion started by: praveen_b744
2 Replies